Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TECHNICAL DATA
Electrical characteristics
Rated power
Type of vacuum cleaner
Number of vacuum motors
Vacuum
Air flow rate
Collection tank capacity
Tank material
Length of power supply cable
Dry weight
Dimensions (length x height x depth)
Accessories diameter
Sound pressure level (ISO 11201)
Uncertainty K
pa
APPLIANCE SAFETY
1. Switch off the appliance by positioning the main switch (1) to "0" (Fig.1).
2. Disconnect the plug (2) on the power cable (3) from the mains power supply socket (4) (Fig.2). To
prevent damaging the power cable, disconnect the plug from the mains socket by directly pulling the
plug and not the cable.
4
1
2
3
1
PREPARING TO WORK
1. Remove the cover (1) from the vacuum tank (Fig.1), using the hooks (2) on the side of the tank
itself (Fig.2).
2. Check that the fabric filter (3) is correctly positioned (Fig. 3)and that the collection bag (4) is correctly
inserted inside it (Fig. 4).
1
2
1
3. Fix the cover (1) on top of the vacuum tank (Fig.5), locking it using the hooks (2) on the side of the
tank itself (Fig.6).
1
4
4
4. Insert the nozzle (5) in the vacuum hose into the hole on the vacuum tank cover (Fig.7).
5. Connect the handle (6) in the vacuum hose with the telescopic tube (7) (Fig.8).
6. Select the most suitable accessory for the work to be carried out. Connect the accessory (8) to the
telescopic tube (7) (Fig.9).
7. Connect the plug (9) on the power cable to the socket (10) in the appliance (Fig.10).
6
5
7
7
10
9
10
10071827-AA_UM_FV9 E.indb 17
U.M.
FV9+
FV9+
[SI]
230 V
115 V
V - Hz
230 - 50
120 - 60
W
950
1000
Dry
1
kPa
21
22
m
/h
104
3
l
6
HDPE
m
15
kg
5.7
cm
26.5x22.3x49.6
mm
32
dB (A)
79.4
75
dB (A)
1.5
1.5
2
3
2
3
2
5
6
8
9
1. Insert the plug (1) of the power supply cable (2) in the mains supply socket (3) (Fig.1).
2. Switch on the machine by setting the main cut-off switch (4) to "I" (Fig. 2).
3. If the combined brush is used set the switch (5) in the brush head to "HARD SURFACE" or "CARPET
FLOOR" depending on the floor you want to work on (Fig.3).
4. Proceed with the vacuuming.
N.B.: If the vacuuming capacity is too high, shift the lever (6) on the vacuum hose handle (Fig. 4)
while the accessory is in contact with the floor.
3
1
4
2
1
6
4
AT THE END OF THE WORK
1. Make sure the machine has been secured (see the section titled
2. Take the appliance to the designated place for emptying the tank.
3. Carry out the procedures described in the chapter "MAINTENANCE".
4. Position the appliance on a flat surface in an enclosed place; there must be no objects near the
appliance that could either damage it, or be damaged through contact with it. If you decide to hang
the appliance on supports, make sure they are able to sustain its volume and weight.
MAINTENANCE
1. Make sure the machine has been secured (see the section titled
2. Remove the vacuum nozzle (1) from the hole in the cover (2) of the appliance, turning it anti-clockwise
(Fig.1).
3. Remove the cover (2) from the vacuum tank (Fig.2), using the hooks (3) on the side of the tank
itself (Fig.3).
2
1
1
4. Remove the collection bag (4) from the tank (Fig.4). Change it if necessary.
N.B.: If fabric dust collection bags are used, instead of paper ones, empty them and clean
them with a jet of air, check their condition and change them if necessary.
5. Remove the fabric filter (5) from the appliance (Fig.5).
N.B.: If the surface of the filter is extremely dirty, brush the filter with a normal soft brush to clean
it thoroughly, and if necessary wash it in water.
ATTENTION: Check the condition of the cloth filter if the filter surface area is particularly clogged
or if it is damaged replace it.
6. Clean the inside of the collection tank with a damp cloth.
7. Insert the fabric filter (5) in the tank (Fig.6).
WARNING: Before inserting the fabric filter (5) in the tank, wait until it is completely dry if it was
previously washed.
ATTENTION: When inserting the fabric filter (5) into the tank, make sure that the gasket sticks
completely to the edge of the tank, so as not to compromise the vacuum being effective.
7
4
5
8
4
8. Insert the collection bag inside the collection tank (4) (Fig.7)
9. Put the cover (2) over the vacuum tank (Fig.8), securing it with the hooks (3) on the side of the tank
itself (Fig.9).
ATTENTION: When fitting the cover (2) make sure that the nozzle (6) in it fits correctly in the hole
in the collection bag (4) (Fig.8).
10. Disconnect the vacuum hose (6) from the cover (2) (Fig.10).
11. Clean the inside of the vacuum hose with a jet of compressed air, if necessary removing any
obstructions.
12. Disconnect the cleaning accessory.
17
WORK
2
3
"SECURING THE
MACHINE").
"APPLIANCE
SAFETY").
3
2
3
5
5
6
5
13/11/2017 14:30:09
Publicidad
Capítulos
Tabla de contenido
