Technical Data; Circular Saw; Vibration Information; Circular Saw Safety Warnings - AEG KS15-1 Manual Original

TECHNICAL DATA

Circular saw

Production code
Rated input
No-load speed
Voltage
Saw blade dia. x hole dia
Saw blade thickness
Blade teeth
Max. Cutting depth at 0° / 45° / 56°
Weight according EPTA-Procedure 01/2014
Recommended Ambient Operating
Temperature
Noise information
GB
Measured values determined according to EN 62841. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!

Vibration information

Vibration total values (triaxial vector sum) determined according
to EN 62841
Sawing of wood:
Vibration emission value a
Uncertainty K= 3dB(A))
WARNING
The vibration and noise emission level given in this information
sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the
main applications of the tool. However if the tool is used for di er-
ent applications, with di erent accessories or poorly maintained,
the vibration and noise emission may di er. This may signi cantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should
also take into account the times when the tool is switched o or
when it is running but not actually doing the job. This may signi -
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the e ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work
patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and speci cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
English Deutsch
18
425_273_KS15_1-2.indd 18
KS15 -1
4749 96 01 ...
... 000001-
999999
1500 W
5000 min
-1
220-240V AC
50/60Hz
190 x 30 mm
2,2 mm
24
62 / 47 / 36 mm
4,2 kg
-18°C ... +50°C
94,5 dB(A)
105,5 dB(A)
1,5 m/s 2
2
4,2 m/s
h,W

CIRCULAR SAW SAFETY WARNINGS

Cutting procedures
a) DANGER: Keep hands away from cutting area and
the blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they cannot be
cut by the blade.
b) Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the work-
piece. Less than a full tooth of the blade teeth should be visible
below the workpiece.
d) Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a stable
platform. It is important to support the work properly to minimise
body exposure, blade binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a „live"
wire will also make exposed metal parts of the power tool „live"
and could give the operator an electric shock.
f) When ripping, always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces the chance
of blade binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run o -centre, causing loss of
control.
h) Never use damaged or incorrect blade washers or bolt.
The blade washers and bolt were specially designed for your saw,
for optimum performance and safety of operation.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, jammed or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
– when the blade is pinched or jammed tightly by the kerf closing
down, the blade stalls and the motor reaction drives the unit
rapidly back toward the operator;
– if the blade becomes twisted or misaligned in the cut, the teeth
at the back edge of the blade can dig into the top surface of the
wood causing the blade to climb out of the kerf and jump back
toward the operator.
Kickback is the result of saw misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
a) Maintain a rm grip with both hands on the saw and
position your arms to resist kickback forces. Position your
body to either side of the blade, but not in line with the
blade. Kickback could cause the saw to jump backwards, but kick-
back forces can be controlled by the operator, if proper precautions
are taken.
08.11.19 08:50