TTM BIG300 Professional Manual Del Usuario página 4

2.5 SET Flash/P-T /illegal dialing prevention
When LCD displays
setting. Then LCD will display
1 Press "1" to enter flash time setting, LCD shows
is 600ms), is twinkling, press "UP" or "DOWN" to set the desired time. There are 8
choices: 90, 95,100,120,180,300,600 and 1000ms.
2 Press "2" to enter P-T switch mode and the LCD prompt
The .default setting is TONE.
TONE to PULSE.
3 Press "3" to enter illegal dialing prevention setting. LCD shows
is twinkling, then press "UP" or "DOWN" to toggle from OFF to ON.
During each step, press "FLASH/SET" to confirm and
2.6 SET Local area code/ Out area code
When LCD displays
code setting. Then LCD will display
1. Press "1" to enter local area code setting. LCD shows
" " is twinkling, Input numbers directly. There are 8 digits number can be
stored.
2. Press "2" to enter out area code setting.LCD prompts
is twinkling, directly to input number to activate this function while its default setting
is OFF. There are 8 digits number can be stored.
3. During each step, press "FLASH/SET" to confirm and
2.7 LCD brightness adjustable
When LCD displays
will display " LCD Con 4", "4" is twinkling, press "UP+" or "DOWN-" to adjust the LCD
brightness (Total 5 levels). 1 is the darkest and 5 is the brightest. The default value is 4.
Press "FLASH/SET" to save the setting and
Remark: When LCD display becomes weaker, please change the batteries by new ones.
Press 5 to enter Flash time/P-T/ Anti-parallel
(the default value
is twinkling, press "UP" or "DOWN" to toggle from
to exit.
Press 6 to enter local area code and out area
to exit.
Press 7 to enter LCD contrast setting. Then LCD
to exit.
2.8 SET IP
When LCD displays
Then LCD will display
1 Press "1" to enter the auto-IP code setting,
blinking. Press "UP+" or "DOWN-" to choose the desired IP number and press SET to
confirm. The following numbers for selection:
IP1, IP2, 17909, 17908, 193, 17911, 17921, 17931, 17951, 17991, 068, 96300, 96333, 196,
.
190, 17969, 197.
2 Press "2" to enter setting the IP number manually. LCD displays
input the new IP number and press DEL to modify, press "FLASH/SET" finally to save.
,
3 Press "3" to enter the second Manual IP setting, setting procedure please refer to the first
one.
Press "FLASH/SET" to save the setting and
3. On-hook Operation
3.1 Reviewing the incoming calls
At On-hook status or off-hook status, press "UP+" or "DOWN-" to review all the incoming
call numbers, press "#" key for 3 seconds also can go into the incoming inquiry state.
,
3.2 Call back
When viewing incoming or outgoing calls, find the desired number, press "BACK/÷" to call
back directly. Holding "BACK/÷" key for 3 seconds phone will auto-add 0 before the number
you want to call back.
,
3.3 Reviewing the outgoing calls
At On-hook status or off-hook status, press "CHECK/×" to review the outgoing calls, using
"UP+" or "DOWN-" to backward or upward review the number, date and time of outgoing
calls.When on-hook state, pressing "*" for 3 seconds also can go into the outgoing inquiry
state.
3.4 Pre-dialing function
At on-hook state, you can input the calling number directly (edit the mistake with the DEL
key), then press BACK/÷ or
3.5 DEL function
During the setting model, using DEL key to exit. In pre-dialing, use DEL key to delete the
wrong numbers. During the review of incoming, outgoing & stored numbers, use DEL key to
delete the certain number. If hold DEL key for 3 seconds, all the incoming & outgoing calls
will be deleted.
Press 8 to enter IP setting.
on LCD with
to exit.
key to dial out.
directly