List Of Available Menus - Carel WTS compact Manual Del Usuario

ENG

3.8 List of available menus

1 PROBE CAL. IN Conductivity probe on feed water
2 PROBE CAL. OUT Conductivity probe on permeate
water
3 OUT SET POINT Check the conductivity value at the
outlet. If conductivity exceeds the
set threshold (3B) for a certain time
(3D), it locks in DRIVER ALARM FOR
SYSTEM STOPPING
4 IN SET POINT Check on the conductivity value at
the inlet.
5 LOW LEVEL Min. pressure switch on permeate
line
6 HIGH LEVEL Max. pressure switch on permeate
line
7 MINIMUM Contact of the min. pressure switch
PRESSURE for feed water
8 MAXIMUM Check of the value of max. pressure
PRESSURE downstream of the pump (from
pressure switch calibrated at 12 bar)
9 PUMP TEMP. Protection of the pump motor from
high temperature
10 FILTER Forced system stop when the
upstream softener makes salt
regeneration
11 CLEANING Flushing at the start or after switch-
ing off the system, before or after
each production cycle
WASH CYCLE Flushing of the membranes in a
cyclical way, every "n" hours and for
a variable "x" duration
12 ALARM Output of the alarm signal with
connection to an external device
13 RESET Reset of the counter for the work
hours accumulated by the system
14 SYSTEM TEST Manual procedure to be activated
individually for each single compo-
nent: to be used during the FIRST
START of the system
15 ALARM TEST Check if the alarm output is
operating
16 LANGUAGE Select the display language
17 SET PASSWORD Entering a new password
18 MAINTENANCE Maintenance warning interval
19 DOSING PUMP Locking alarm signal from metering
pump
20 STAND-BY Input for stand-by (remote on-off )
INPUT
21 PUMP DELAY Pump delay, recommended when
a return pump is installed upstream
of the system
"osmosi inversa" +0300017IE rel. 1.4 - 05.04.2018
1a Zero setting of the conductivity probe
1b Setting of the reading scale of the conductivity probe
2a Zero setting of the conductivity probe
2b Setting of the reading scale of the conductivity probe
3a Enabled / disabled
3b Conductivity set point at the outlet (from 0.0 to 99.9
μS)
3c Reading at fl ushing end alarm(locking): enabled /
disabled
3d Delay time for alarm signal (from 0 min 0 sec to 9 min
59 sec)
4a Enabled / disabled
5a Enabled / disabled
5b State of the high level contact (high pressure): N.C. /
N.O.
5c Signal acquisition delay (from 0 to 59 sec)
6a Enabled / disabled
6b State of the high level contact (high pressure): N.C. /
N.O.
6c Signal acquisition delay (from 0 to 59 sec)
7a Enabled / disabled
7b State of the contact with right pressure: N.C. / N.O.
7c Signal acquisition delay (from 0 to 59 sec)
7d Number of attempts before the alarm
7e Alarm during fl ushing as well: YES/NO
8a Enabled / disabled
8b State of the contact with right pressure: N.O. / N.C.
8c Signal acquisition delay (from 0 to 59 sec)
9a Enabled / disabled
9b State of the contact with right temperature: N.C. / N.O.
9c Signal acquisition delay (from 0 to 59 sec)
10a Enabled / disabled
10b State of the contact with active softener: N.C. / N.O.
10c Signal acquisition delay (from 0 to 59 sec)
11a Enabled / disabled
11b Flushing with pump: YES / NO
11c Flushing with charge solenoid valve open: YES / NO
11d Flushing at the beginning of production cycle:
enabled / disabled
11e Duration of the fl ushing from production start
(from 0 to 99 min 59 sec)
11f Flushing at the end of production cycle:
enabled / disabled
11g Duration of the fl ushing from production end
(from 0 to 99 min 59 sec)
11h PERIODIC FLUSHING OF MembraneS: duration of the
fl ushing (from 00 min 00 sec to 99 min 59 sec) and
frequency of the fl ushing (from 00 h to 99 h)
12a Enabled / disabled
12b State of the contact with no alarm: N.C. / N.O.
13a Reset of the hour counter: YES / NO
13b Reset of the time interval before next maintenance:
YES / NO
UP Inlet solenoid valve: enabled / disabled
DOWN Discharge solenoid valve: enabled / disabled
RIGHT Flushing solenoid valve: enabled / disabled
LEFT Pump: enabled / disabled
ENT Metering pump: enabled / disabled
UP Press the arrow up to manually activate the alarm
Italian / English / French / German / Spanish
Key in the new password twice to confi rm the choice
18a Maintenance warning: enabled / disabled
18b Interval before maintenance warning (from 0 to 19999 h)
19a Input for metering pump alarm: enabled / disabled
19b State of the contact with no alarm: N.C. / N.O.
19c Signal acquisition delay (from 0 to 59 sec)
20a Remote input: enabled / disabled
20b State of the contact with no external signal: N.C. / N.O.
20c Signal acquisition delay (from 0 to 59 sec)
21a Start delay of the pump for the reverse osmosis system
after opening the charge solenoid valve (from 0 to
999 sec)
14
ROC025 - ROC040 ROC060
not used (due to the ab- not used (due to the
sence of the conductivity absence of the conduc-
meter at the inlet) tivity meter at the inlet)
not used (due to the ab- already calibrated in the
sence of the conductivity factory
meter at the outlet)
not used (due to the ab- enabled
80 μS
sence of the conductivity
meter at the outlet)
disabled
5 min 00 sec
disabled (due to the ab- disabled (due to the
sence of the conductivity absence of the conduc-
meter at the inlet) tivity meter at the inlet)
enabled enabled
N.C. N.C.
0 sec 0 sec
enabled enabled
N.C. N.C.
0 sec 0 sec
Enabled Enabled
N.C. N.C.
05 sec 05 sec
4 4
YES YES
disabled (due to the enabled
absence of the max.
pressure switch)
- - - N.C.
00 sec 00 sec
disabled (due to the disabled (due to the
absence of temperature absence of temperature
sensor on pump motor) sensor on pump motor)
disabled (due to the disabled (due to the ab-
absence of the upstream sence of the upstream
softener) softener)
disabled enabled
no yes
yes yes
disabled enabled
00 min 00 sec 00 min 20 sec
disabled enabled
00 min 00 sec 00 min 15 sec
00 min 30 sec every 24 h 01 min 00 sec every
08 h
disabled disabled
- - - - - -
absent absent
absent
absent absent
Italian Italian
0077 0077
enabled enabled
240 h 240 h
not used (there is no not used (there is no
metering pump) metering pump)
disabled disabled
- - - - - -
- - - - - -
000 sec 000 sec
Tab. 3.a