Technical Data - AEG BS12C Instrucciones De Uso

TECHNICAL DATA

Drilling capacity in steel ..................................................................
Drilling capacity in wood .................................................................
Wood screws (without pre-drilling) .................................................
No-load speed ................................................................................
Torque
Low torque max.*1 ......................................................................
High torque max.*1 ......................................................................
Static jamming moment .................................................................
Screwing capacity with one fully charged battery (1,5 Ah) : *2
5x60 Soft wood ............................................................................
6x80 Soft wood ............................................................................
Battery voltage ...............................................................................
Weight with battery .........................................................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ..............................................
The noise level when working can exceed 85 dB (A).
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a .........................................................
h
Uncertainty K ...............................................................................
Voltage range .................................................................................
Quick charge current ......................................................................
Maintaining charge .........................................................................
Battery charging time Li-Ion 1,5 Ah ................................................
Weight without cable ......................................................................
*1Measured according to AEG norm N 877318
*2 The values stated are reference values. Actual values might differ, depending on the material and quality of the screws.
*3
80%
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions,
including those given in the accompanying brochure. Failure
to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries
to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System PCLS chargers for charging System PCLS
battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
14 ENGLISH
BS12C (IQ) BS12C (IQ) LL1230 LL1230
............................. 10 mm ............................. 10 mm
............................. 20 mm ............................. 20 mm
............................... 6 mm ............................... 6 mm
........................ 0-575 min ........................ 0-575 min
-1 -1
............................ 9.3 Nm ............................ 9,3 Nm
.......................... 18,5 Nm .......................... 18.5 Nm
............................. 15 Nm ............................. 15 Nm
............................... 141 ............................... 141
................................ 37 ................................ 37
............................. 12 V ............................. 12 V
............................ 1.1 kg ............................ 1,1 kg
............................. 64 dB (A) ............................. 64 dB (A)
......................... < 2.5 m/s ......................... < 2,5 m/s 2 2
............................ 1.5 m/s ............................ 1,5 m/s
2 2
................................. ................................... 12 V ................................. ................................... 12 V
................................. .................................. 3,0 A ................................. .................................. 3,0 A
................................. ........................ max. 500 mA ................................. ........................ max. 500 mA
................................. ............................. ca. 30 min *3 ................................. ............................. ca. 30 min *3
................................. ................................. 466 g ................................. ................................. 466 g
The following battery packs can be charged with this charger:
voltage battery rating
(of storage battery)
12 V L1215 <=1,5 Ah
Do not try to charge non-chargeable batteries with this charger.
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Do not touch the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new one.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by
authorised Service Agents.
This appliance is not intended for use by persons (including
children) with limited physical, sensory or mental capabilities or
insufficient experience and/or knowledge unless they are
supervised by a person who is responsible for their safety or
have been instructed by them in the safe use of the tool.
Children should be supervised in order to ensure that they do not
play with the tool.
SPECIFIED CONDITIONS OF USE
The battery drill/screwdriver is designed for drilling and
screwdriving for independent use away from mains supply.
The quick charger can charge AEG batteries of PCLS.
Do not use this product in any other way as stated for normal
use.
MAINS CONNECTION LL1230
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as the design
conforms to safety class II.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, EN 60335,
EN 61000-3-2, EN 61000-3-3, EN 50 366, in accordance with the
regulations 98/37/EC, 2004/108/EC,
2006/95/EC
Winnenden, 2007-10-09
Manager Product Development
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not been
used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from
being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off and
then on again. If the machine does not start up again, the battery
pack may have discharged completely. In this case it must be
recharged in the battery charger.
CHARACTERISTICS
After inserting the battery into the reception of the charger the
No. of
battery will automatically be charged (red LED stays lit, green
battery
LED flashes).
cells
When a hot or cold battery pack is inserted into the charger
3
(flashing red lamp), charging will begin automatically once the
battery reaches the correct charging temperature (Li-Ion
0°C...60°C).
Charging time varies depending on the battery temperature,
charge needed and the type of battery pack being charged.
As soon as charging is completed, the charger switches over to
"trickle" charge to maintain the full capacity (green control lamp
is illuminated continuously)
It is not necessary to remove the battery after charging. The
battery can be stored permanently in the charger without the
danger of being overcharged.
If both LEDs flash at the same time, either the battery has not
been completely mounted or there is a fault in the battery or the
charger. For safety reasons you must stop using the charger and
battery immediately and have them inspected by an AEG
Customer Service Centre.
MAINTENANCE
If the supply cord of this appliance is damaged, it must only be
replaced by a repair shop appointed by the manufacturer,
because special purpose tools are required
Use only AEG accessories and spare parts. Should components
need to be replaced which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: AEG Elektrowerkzeuge, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Accessory - Not included in standard equipment,
available as an accessory.
Rainer Kumpf
Remove the battery pack before starting any work
on the machine.
This tool is only suitable for indoor use. Never
expose tool to rain.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste electrical
and electronic equipment and its implementation in
accordance with national law, electric tools that
have reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Do not burn used battery packs.
Never charge a damaged battery pack. Replace by
a new one.
Please read the instructions carefully
before starting the machine.
ENGLISH 15