Black and Decker CLM3820 Manual De Instrucciones página 12

ENGLISH
Fitting the grass collection box (fig. I & J)
Lift the clear grass flap (12) and place the grass collection
u
box (9) over the lugs (20).
Wheel height adjustment (fig. K & L)
Your mower features the Black & Decker Easy - height adjust-
ment system. This system will adjust all four wheels at the
same time.
The mower has six blade height adjustment positions (30 mm
to 80 mm). Refer to the scale on the side of the mower. The
pointer will indicate the height setting for cutting your lawn.
This setting can be a reference for the next time you want to
cut your lawn to the same height.
Release the bail bar (2) to turn the lawnmower off, wait
u
until the blade stops and remove the safety key (1).
To raise or lower the cutting height, place the palm of your
u
hand on the palm rest (21) and pull the height adjustment
lever (13) away from the mower body.
Move the height adjust lever (13) into the required position
u
then push it back in towards the mower body.
Note: Make sure that the mower is securely locked in one of
the six positions.
Removing and fitting the battery (fig. O)
Before removing the battery:
Place the mower on level ground.
u
Release the bail bar (2) to turn the mower off, wait for the
u
blade to stop and remove the safety key (1).
To remove the battery:
Pull the battery cover release (15) towards the front of the
u
mower body and lift the battery cover (14).
Lift the battery (22) out of the mower.
u
To fit the battery
Pull the battery cover release (15) towards the front of the
u
mower body and lift the battery cover (14).
Slide the battery (22) into the mower. (the battery will only
u
fit one way.)
Use
Warning! Let the appliance work at its own pace. Do not
overload.
Charging the battery (fig. M)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
12
(Original instructions)
To charge the battery (22), insert it into the charger (23).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (24) will flash green continuously
(slowly).
The charge is complete when the charging indicator (24)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops off the battery charge. The charging indica-
tor (24) will be lit as long as the battery is connected to the
plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (24) will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (22).
u
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original bat-
u
tery is defective and should be returned to a service centre
for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
State of charge indicator (fig. N)
The battery is fitted with a state of charge indicator. This can
be used to display the current level of charge in the battery
during use and during charging.
Press the state of charge indicator button (25).
u
Safety key (fig. P)
Remove the safety key:
Whenever leaving the appliance unattended.
u
Before cleaning a blockage.
u
Before checking, cleaning or working on the appliance.
u
After striking a foreign object.
u
Whenever the appliance starts vibrating abnormally.
u
Switching on and off (fig. P & Q
Warning! Sharp moving blade. Never attempt to override the
operation of this switch and safety key system as a serious
injury could result.