On/Off Switch - Black and Decker KA270 Manual De Instrucciones

g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for sanders
Always wear a dust mask whenever sanding.
x
Thoroughly remove all dust after sanding.
x
Take special care when sanding paint which is possibly
x
lead based or when sanding some woods and metal
which may produce toxic dust:
- Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that persons
within or entering the work area are also protected.
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
Before using the tool on wooden workpieces, make sure
x
to fit the dust cassette.
Before using the tool on metal workpieces, make sure to
x
remove the dust cassette.
Never use the tool without a sanding sheet.
x
Never use the tool without a sanding base.
x
This appliance is not intended for use by young or infirm
x
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
x
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
This tool includes some or all of the following features.

1. On/off switch

2. Gel comfort grip (KA270GT(K) only)
3. Dust cassette
4. Large detail sanding base
5. Tip holder
6. Sanding base tip
Fig. A
7. Random orbit sanding base
8. Profile attachment (KA270(GT)K only)
9. Sanding profiles (KA270(GT)K only)
10. Detail finger attachment (KA270(GT)K only)
11. Spare sanding base tip (KA270(GT)K only)
12. Louvre attachment (KA270LDK only)
Assembly
Warning! Before assembly, make sure that the tool is switched
off and unplugged.
Random orbit sanding base
With this sanding base, you can use the tool as a random orbit
sander.
Fitting and removing the sanding base (fig. B)
Place the sanding base (7) onto the spindle (13).
x
Place the washer (14) onto the spindle.
x
Insert the Allen screw (15) into the screw hole in the spindle.
x
Tighten the Allen screw using the Allen key (16) supplied.
x
To remove the sanding base, remove the Allen screw (15)
x
and washer (14).
Fitting sanding sheets (fig. C)
Hold the tool with the sanding base (7) facing upwards.
x
Place the sanding sheet (17) onto the sanding base (7).
x
The holes in the sheet do not need to line up with the
holes in the base.
Large detail sanding base
With this sanding base, you can use the tool as a detail
sander or an orbital sander.
Fitting and removing the sanding base (fig. D & E)
For detail sanding, the pointed end should face forward as in
fig. D. For sanding large areas, the pointed end should face to
the back as in fig. E.
Place the sanding base (4) onto the spindle (13). Make
x
sure that the legs of the base locate into the tool.
Place the washer (14) onto the spindle.
x
Insert the Allen screw (15) into the screw hole in the spindle.
x
Tighten the Allen screw using the Allen key (16) supplied.
x
To remove the sanding base, remove the Allen screw (15)
x
and washer (14).
ENGLISH
7