Protecting The Environment - Black and Decker BDT555KIT Manual De Instrucciones

When the wound cutting line reaches the recesses (24),
u
cut the line. Let the line protrude approx. 11 cm from the
spool and hold a finger on the line to keep it in place (fig.
M).
Proceed as described above to fit the spool on the tool.
u
Warning! Only use the appropriate type of BLACK+DECKER
cutting line.
Troubleshooting
If your tool seems not to operate properly, follow the instruc-
tions below. If this does not solve the problem, please contact
your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
Check that the spool housing can rotate freely. Carefully
u
clean it if necessary.
Check that the cutting line does not protrude more than
u
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover
u
from the housing.
Pull the cutting line until it protrudes 11 cm from the hous-
u
ing. If insufficient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
Align the tabs on the spool cover with the cut outs in the
u
housing.
Push the cover onto the housing until it snaps securely
u
into place.
If the cutting line protrudes beyond the trimming blade, cut
u
it off so that it just reaches the blade.
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
Carefully clean the spool cover and housing.
u
Remove the spool and check if the lever can move freely.
u
Remove the spool and unwind the cutting line, then wind it
u
on neatly again as described above. Replace the spool as
instructed.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory opera-
tion depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
(Original instructions)
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
u
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft
u
brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt
u
from the underneath of the guard.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com
Technical data
Input Voltage
V
AC
Power Input W
No-Load Speed min
-1
Weight kg
Level of sound pressure:
Sound pressure (L ) 80 dB(A), uncertainty (K) 1.0 dB(A)
pA
Sound power (L ) 94.8 dB(A), uncertainty (K) 1.0 dB(A)
WA
Vibration total values (triax vector sum) according to EN 786:
Vibration emission value (a ) 3.8 m/s
h
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
ENGLISH
BDT555KIT Type 1
, uncertainty (K) 1.5 m/s
2 2
%
230
550
7500
2.5
9