DeWalt DCS577 Traducido De Las Instrucciones Originales página 49

Bevel Angle Adjustment (Fig. A, F)
The full range of the bevel adjustment is from 0˚ to 53˚.
Detents are located at 22.5˚ and 45˚. The angle quadrant
is graduated in increments of 1˚. On the front of the saw is
a bevel angle adjustment mechanism which consists of a
calibrated angle quadrant
10
The angle quadrant allows for coarse adjustment
adjustment 17 to achieve better accuracy in cutting.
To Set the Saw for a Bevel Cut
1. Lift the bevel adjustment lever
desired angle by aligning the pointer with the desired
angle mark.
2. Push the bevel adjustment lever down and tighten securely
to lock the angle.
Base Plate Adjustment (Fig. F, G)
Your base plate has been factory set to assure that the blade is
perpendicular to the base plate. If after extended use you need
to re‑align the blade, follow the directions below:
Adjusting for 90 Degree Cuts
1. Return the saw to 0 degrees bevel.
2. Place the saw on its side, and retract the lower guard.
3. Set the depth of cut to 51 mm.
4. Loosen the bevel adjustment lever (Fig. F,
against the blade and the base plate as shown in Figure G.
5. Using a hex key ( , Fig. A), turn the set screw (
21
on the underside of the base plate until the blade and
the base plate are both in flush contact with the square.
Retighten the bevel adjustment lever.
Adjusting Bevel Adjustment Lever (Fig. F)
It may be desirable to adjust the bevel adjustment lever
may loosen in time and hit the base plate before tighten ing.
To tighten the lever:
1. Hold the bevel adjustment lever
adjustment lever locknut (
2. Adjust the bevel adjustment lever by rotating it in the
desired direction about 1/8 of a revolution.
3. Retighten nut.
Kerf Indicator (Fig. H)
The front of the saw foot plate
a 45˚ kerf indicator for vertical and bevel cutting. The kerf
8
indicators enable you to guide the saw along the cutting lines
penciled on the workpiece.
The indicator aligns with the left (outer) side of the saw blade.
The moving blade making the slot or "kerf" cut falls to the right
of the indicator. Position the saw along the penciled cutting line
so that the kerf falls into the waste or surplus material. Marking
indicators on the front of the foot plate are at 13 mm intervals
for additional cutting guides.
Kerf indicators 18 are also located on the inside of the foot
plate to keep the saw square when cutting.
and a bevel adjustment lever
9
16 or fine
9 and tilt foot plate to the
9 ). Place a square
, Fig. G)
25
. It
9
9 and loosen the bevel
, Fig. F).
24
5 has a 0˚ kerf indicator 7 and
Cut Length Indicator (Fig. I)
The markings on the side of the foot plate
the slot being cut into the material at the full depth of the cut.
The markings are in increments of 3.2 mm.
D WALT Bluetooth® Tool Tag Ready (Fig. J)
e
.
Optional Accessory

WARNING: Read instruction manual for the D
Bluetooth® Tool Tag.

WARNING: Turn tool off and disconnect battery pack
before installing the D

WARNING: When installing or replacing the D
Bluetooth® Tool Tag, use only the screws provided. Be sure
to securely tighten the screws.
Your tool comes with mounting holes
installing a D WALT Bluetooth® Tool Tag (DCE041). You will
e
need a T15 bit tip to install the tag. The D
designed for tracking and locating professional power tools,
equipment, and machines using the D
app. For proper installation of the D
D WALT Tool Tag manual. To learn more visit:
e
www.dewalt.com/en‑us/jobsite‑solutions/tool‑connect
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
IMPORTanT: Always make sure the depth adjustment locking
lever is in the down position before operating saw.
Proper Hand Position (Fig. K)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle , with the other hand on the auxilliary handle
12
Note that hands are kept away from cutting area.
Trigger Switch (Fig. A)

WARNING: To reduce the risk of serious personal
injury, hold saw with both hands when starting the
saw to avoid kickback.
Press the trigger switch 2
trigger switch to turn the tool off.
nOTE: This tool has no provision to lock the trigger in the on
position and should never be locked on by any other means.
EnGLISH
show the length of
5
WALT
e
WALT Bluetooth® Tool Tag.
e
WALT
e
33 and fasteners for
WALT Tool Tag is
e
WALT Tool Connect™
e
WALT Tool Tag refer to the
e
13
to turn the tool on. Release the
.
47