Horizon Global 76177 Instrucciones De Instalación página 3

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Always wear SAFETY GLASSES
when installing hitch
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequentgro
up.com/qr-product.aspx
1. Remove plastic fascia stabilizer – using a flat head screwdriver, remove (2) plastic push rivets holding plastic stabilizer in place. Note: There are two plastic tabs
holding this piece into place. They can be removed by pinching them or rotating the whole stabilizer.
2. Lower muffler – Using the exhaust removal pliers, lower muffler by removing the (4) rearmost rubber hangers. Note: A spray a lubricant on rubber hangers makes
them slide off metal pins more easily. NOTE: Be careful that exhaust is supported before removing rubber hangers.
3. Remove rear tow hook – remove (6) M12 bolts using an 18mm socket and extension. There are (3) bolts on the lower surface of the hook and (3) bolts on the side. Set
bolts aside for reinstallation later. Note: There is a black plastic module located near the side bolts. To move this for easier access, simply pull the module toward the
passenger side of the vehicle, it will come off of the clip.
4. Widen the hole – on the driver side of the vehicle there is a hole located between middle and forward most holes. Using a die grinder, widen the hole enough so that
one of the blocks fits into the frame.
5. Install blocks and carriage bolts – using the provided fish wire (part no. 5481), push the (2) carriage bolts into the hole widened previously, insert the (2) blocks into
the holes, and pull the fish wire out, ensuring the bolts are seated into the blocks. See figure 2 for an illustration.
6. Raise hitch into position – raise the hitch over the tailpipe(s) and align holes in the hitch bracket with existing weldnuts in frame rail.
7. Install fasteners - Install (4) M12 bolts and (2) hex nuts and (2) conical toothed washers as shown in figure 1.
8. Tighten all M12 CL10.9 fasteners with torque wrench to 105Lb.-Ft. (142N*M). Tighten all hex nuts to 75Lb.-Ft. (149N*W).
Proper torque is needed to keep the hitch secure to the vehicle when towing.
9. Replace the module you removed in step 3
10.Raise muffler – raise muffler back into position and reattach rubber hangers, (2) per side.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced.
Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2017 Horizon Global Americas Inc. - Printed in Mexico
Installation Instructions
PART NUMBERS: 76177, 84177, CQT76177
n
j
m
k
l
Rear
Hole to enlarge
Frame rail
Existing hardware
Figure 1
Sheet 3 of 18
Fastener Kit: 76177F
Qty.(2)
Pull wire 7/16
Part no. 5481
Qty. (2)
Conical Tooth
Washer 1/2"
l
Qty. (2)
Hex Nut
1/2 - 13
m
Qty. (2)
Block 1"x2"
Part no. 5121
n
Qty. (2)
Carriage Bolt
1/2 – 13 x 1.25
Conical Washer
Kink pullwire to keep spacer
independent of bolt
Figure 2
76177NP
6-28-17
Teeth side
Against hitch
Rev. A

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

84177Cqt76177

Tabla de contenido