GRAPHITE 58G024 Instrucciones De Uso página 12

• Always keep the battery away from sources of heat. Do not leave
the battery for a long time in high temperature (in direct sunlight,
in proximity of heaters and wherever the temperature exceeds
50°C).
• Do not expose the battery to fire or excessive temperature.
Exposure to fire or temperature above 130°C may cause explosion.
CAUTION! Temperature of 130°C can be also defined as 265°F.
• Observe all charging instructions. Do not charge the battery
in temperature outside of range defined in the rating data
table from the instruction manual. Incorrect charging or
charging in temperature outside of defined range may damage the
battery and increase the risk of fire.
BATTERY REPAIRS
• Do not repair damaged batteries. Battery can be repaired only by
the manufacturer or in an authorised workshop.
• When disposing of the worn out battery, take it to a service
point where you can utilize such dangerous wastes.
SAFETY REGULATIONS FOR THE CHARGER
• Do not expose the charger to humidity or water. Ingress of
water into the charger increases risk of electric shock. Use the charger
only in dry rooms.
• Disconnect the charger from power supply before starting any
maintenance or cleaning.
• Do not use the charger when placed on flammable surface
(e.g. paper, textiles) or in proximity of flammable substance.
Greater charger temperature when charging increases risk of fire.
• Check condition of the charger, cable and plug before each
use. Do not use the charger if any damage is found. Do not
try to disassemble the charger. All repairs should be made at an
authorized service workshop. Improper charger assembly may cause
electric shock or fire.
• Children or persons who are physically, emotionally or mentally
disabled and other persons, whose experience or knowledge
is insufficient to use the charger while following all safety rules
should not use the charger without supervision of person
responsible for their safety. Otherwise there is a risk of improper
use and injuries in consequence.
• When the charger is not in use, it should be disconnected from
the mains network.
• Observe all charging instructions. Do not charge the battery
in temperature outside of range defined in the rating data
table from the instruction manual. Incorrect charging or
charging in temperature outside of defined range may damage the
battery and increase the risk of fire.
CHARGER REPAIRS
• Do not repair damaged charger. The charger can be repaired only
by the manufacturer or in an authorised workshop.
• When disposing of the worn out charger, take it to a service
point where you can utilize such wastes.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of injuries at work.
Li-Ion batteries may leak, set on fire or explode when heated to
high temperature or short-circuited. Do not store the batteries
in a car in hot and sunny days. Do not open the battery. Li-Ion
batteries contain electronic protection devices that, if damaged,
may cause fire or explosion of the battery.
Explanation of used symbols
1 2
5 6
9 10
Read instruction manual, observe warnings and safety
1.
conditions therein.
Use protective goggles and hearing protectors.
2.
Keep the tool away from children.
3.
Protect against rain.
4.
Use indoors, protect from water and moisture.
5.
Recycling.
6.
Protection class 2.
7.
Segregated waste collection.
8.
Do not throw cells into fire.
9.
Hazardous to water environment.
10.
Do not allow to heat above 50°C.
11.
CONSTRUCTION AND USE
The impact driver is a battery-powered tool. Drive consists of a
brushless DC motor with planetary gear. The impact driver is used
for tightening and undoing screws and bolts in wood, metal or
plastics. High speed allows to use the device widely for self drilling
screws, and high torque allows to use the device for long screws in
wood. The device can be well used at heights and in hard to reach
areas. High torque mechanism creates the torque as short, high
peaks of circumferential impact, and tool reaction towards the
operator's hands during tightening is low.
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Tool holder
1.
Fixing sleeve of the tool chuck
2.
Casing
3.
Direction selector switch
4.
Handle
5.
Holder
6.
Illumination
7.
Gear switch button
8.
Gear display
9.
Switch
10.
Battery lock button
11.
Battery
12.
Charger
13.
LED diodes
14.
12
3 4
7 8
Max.
50°C
11