BURG-WACHTER FireProtec FP 44 E Instrucciones De Uso página 2

User manual
Structure
Bolts Knob
Display
Program button
Start button
Cover for bottom-
Number-Buttons
fixing position
Battery cover
Tray
Dear customer,
Thank you for choosing the FireProtec FP 44 E safe by BURG-WÄCHTER.
Please read the entire instruction manual before programming and keep this manual
safe so that you can revisit it at a later date.
We hope you enjoy your new BURG-WÄCHTER safe.
Your Burg-Wächter KG
Increasing burglary protection
Please take care to ensure codes do not fall into the wrong hands. Therefore, store the
codes in a safe location so that they can only be accessed by authorised persons. In the
event you lose a code, the lock must be set to a new code.
• The factory code must be changed as soon as the lock is commissioned
• Codes that are easy to guess (e.g. 1, -2, -3, -4, -5, -6) must not be used
• Personal data (e.g. birthdays) or other data that may be guessed with
knowledge of the code owner must not be used as a code
• After changing the code, the lock must be checked several times with the safety door
opened
Attention: All changes to user codes must be carried out with the safe door open! After
changing a code, the lock must be operated several times with the new code with the safe
door open.
Opening
• Press the „Start button", the display shows „------"
• Input one of your two 6-digit user codes. If correct the display shows „OPEn"
and the green LED will light up
• Turn the knob clockwise
• Open the door
Tip: The safe can be opened in security mode by pressing the start button
twice at the beginning The user code entered is not shown in the display.
BURG-WÄCHTER KG
Altenhofer Weg 15 58300 Wetter
• •
Closing
• Close the door
• Press the „Start button", the display shows „------"
• Input one of your two 6-digit user codes. If correct the display shows „OPEn"
and the green LED will light up
• Turn the knob counter clockwise
Tip: The safe can be closed in security mode by pressing the start button twice
at the beginning. The user code entered is not shown in the display.
Kleylock
It is possible to lock the keyboard to prevent accidental input.
• To activate, press the start button for 3 seconds. The message "Act" appears
in the display The key lock is activated.
• Press the start button again for 3 seconds to deactivate. The message "dEAct"
appears in the display The keyboard is active again.
Programming code(s)
The FP 44 e-safe allows for the creation of two different user codes. The code position to be
programmed is selected during the following programming steps. Both user codes open
the safe in the same way.
• Open the safe door
• Remove the cover, bottom left on the inside of the safe door
• Press the programming button situated behind it
• The display shows "-CodE-", followed by "USEr_".
• On the keyboard, select 1 for user code 1 or 2 for user code 2
• Press the Start button. The message "------" appears in the display
• Enter a new 6-digit user code
• The display shows the message "AgAIn", followed by the message
"------"
• To confirm, re-enter the 6-digit user code
• As confirmation "In_1" or "In_2" appears in the display. and the
green LED illuminates
• Test the new user code with the door open
Input-sounds
Switch the key and notification tones off and on again as follows This does not apply to the
alarm tone if a user code is entered incorrectly several times.
• Open the safe door
• Remove the cover, bottom left on the inside of the safe door
• Press and hold the programming button situated behind it for 3 seconds
• The green LED illuminates and a warning tone sounds. The display shows the message
"On-OFF"
• Select 1 to turn the sound off or 0 to turn it on
• Confirm your selection with the start button
Changing batteries
• Remove the battery cover
• Take out the old batteries
• Insert four new batteries with correct alignment
(4 x MIGNON LR6 / AA / ALKALINE)
• Replace the battery cover
Attention: If the battery voltage is too low, "Lo_bAt" appears on the display.
All four batteries need to be replaced in such case.
Germany www.burg.biz
• •
Technical data
Wrong code entries After 5 wrong code entries an alarm
sounds for 3 minutes. The alarm can
be cancelled by correctly entering
a user code
Power supply 4 x MIGNON LR6 / AA / ALKALINE
Certified protection against fire At an external temperature of approx.
SPCR 002 RISE, fire resistance class 1000°C, after one hour the inside temper-
NT FIRE 017 - 60 Paper ature increases less than 150°C measured
from the initial temperature
Warranty
BURG-WÄCHTER products comply with the technical standards at the time of production
and adhere to our own quality standards. The guarantee only covers defects which can
be proved to have resulted from production or material defects at the time of purchase.
The warranty ends after two years, further claims are excluded. Defects and damage
caused by e.g. transport, incorrect operation, improper use, wear etc. are excluded from
the warranty. The batteries are not included in the guarantee. A short description of any
defects identified must be made in writing and the device returned to the place it was
purchased, together with the original packaging. After the device has been tested, and
within a appropriate period of time, the guarantor will decide whether or not to repair or
exchange the item.
Attention:
In order to deliver a flawless and high quality product to you and to better assist you in
case of service or repair, it is necessary that faulty or defective devices along with the valid
usercode be presented to your dealer together with the original documentation.
For returns, all undamaged device parts must furthermore be in the factory setting due to
your right of revocation. Failure to comply with this will invalidate the warranty.
Disposal of the device
Dear customer,
please help us avoid unnecessary waste. Should you intend to dispose of this device at any
time, please remember that many components of this device contain valuable materials
that can be recycled.
Please be aware that electrical and electronic equipment and batteries marked in
this way must not be disposed of with household waste but collected separately.
Please obtain information on the collecting points for electrical waste from the
responsible authority of your city/municipality.
BURG-WÄCHTER KG hereby declares that this device complies with the Directives
2014/30/EU, (EMC) and 2011/65/EU (RoHS).
The complete text of the EU Declaration of Conformity is available at the
following Internet address: www.burg.biz
Printing and typesetting errors as well as technical changes reserved.
FireProtec FP44 E | ENGLISH