Auto Button; Pcm Button; Dts Button; Analog Button - Denon AVR-3802 Instrucciones De Operación

Playing the input source
1 1 5
B
2 3
1
Select the input source to be played.
Example: CD
FUNCTION
CD
3
(Main unit) (Remote control unit)
To select the input source
SOURCE
when REC MULTI OUT or
TUNING PRESET is selected,
press the SOURCE button
then operate the input function
(Main unit)
selector.
2
Select the input mode.
• Selecting the analog mode
Press the ANALOG button to switch to the
analog input.
ANALOG
ANALOG
(Main unit) (Remote control unit)
• Selecting the external input (EXT. IN) mode
Press the EXT. IN (on the EXT. IN button on
the remote control unit) to switch the external
input.
EXT.IN
EXT.IN
(Main unit) (Remote control unit)
• Selecting the AUTO, PCM and DTS modes
The mode switches as shown below each
time the INPUT MODE button is pressed.
MODE
AUTO PCM DTS
(Remote control unit)
• Selecting the AUTO mode
Press the AUTO button to switch to the auto
mode.
AUTO
(Main unit)
All manuals and user guides at all-guides.com
BAND MODE
CHANNEL VOLUME
TUNING
+
+
SKIP ENTER
4
-
-
SHIFT
SKIP
MUTING
TUNER PHONO CD
1 2 3
CDR/TAPE VDP DVD
1
4 5 6
VCR-1 VCR-2/V.AUX TV/DBS
7 8 9
TV/
0 +10
VCR
RDS PTY RT
TEST
SPEAKER OUTPUT
TONE
SURROUND
DOLBY/DTS DSP 5CH / 7CH
SIMU. STEREO
SURROUND
3
6.1 / 7.1
DIRECT STEREO
SURROUND
INPUT
2
MODE ANALOG EXT.IN
SYSTEM CALL
CALL 1 CALL 2 BACKLIGHT
Input mode selection function
Different input modes can be selected for the different
input sources. The selected input modes for the separate
input sources are stored in the memory.
q AUTO (auto mode)
In this mode, the types of signals being input to the
digital and analog input jacks for the selected input
source are detected and the program in the AVR-
3802's surround decoder is selected automatically
upon playback. This mode can be selected for all input
sources other than PHONO and TUNER.
The presence or absence of digital signals is detected,
the signals input to the digital input jacks are identified
and decoding and playback are performed
automatically in DTS, Dolby Digital or PCM (2 channel
stereo) format. If no digital signal is being input, the
analog input jacks are selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM
signals are being input.
Note that noise may be generated when using this
mode to play signals other than PCM signals.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS
signals are being input.
r ANALOG (exclusive analog audio signal playback
mode)
The signals input to the analog input jacks are decoded
and played.
t EXT. IN (external decoder input jack selection mode)
The signals being input to the external decoder input
jacks are played without passing through the surround
circuitry.
NOTE:
• Note that noise will be output when CDs or LDs
recorded in DTS format are played in the "PCM"
(exclusive PCM signal playback) or "ANALOG"
(exclusive PCM signal playback) mode. Select the
AUTO or DTS mode when playing signals recorded in
DTS from a laser disc player or CD player.
Note on playing a source encorded with DTS
• Noise may be generated at the beginning of
playback and while searching during DTS
playback in the AUTO mode. If so, play in the
DTS mode.
• Selecting the PCM mode
Press the PCM button to switch to the PCM
signal input.
PCM
(Main unit)
• Selecting the DTS mode
Press the DTS button to switch to the DTS
signal input.
DTS
(Main unit)
3
Select the play mode.
Example: Stereo
SURROUND SELECT
MODE
STEREO
(Main unit) (Remote control unit)
To select the surround mode
SURROUND
MODE
while adjusting the surround
parameters, channel volume or
tone control, press the
surround mode button then
(Main unit)
operate the selector.
4
Start playback on the selected component.
• For operating instructions, refer to the
component's manual.
5
Adjust the volume.
VOLUME
MASTER VOLUME
+
-
The volume level is
displayed on the
(Main unit) (Remote control unit)
master volume level
display.
The volume can be adjusted within the range of
–70 to 0 to 18 dB, in steps of 1 dB. However, when
the channel level is set as described on page 13 or
page 27, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to
18 dB. (In this case the maximum volume
adjustment range is "18 dB — (Maximum value of
channel level)".)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs
are played in the "ANALOG" or "PCM" mode.
When playing DTS-compatible sources, be sure to
connect the source component to the digital input
jacks (OPTICAL/COAXIAL) and set the input mode to
"DTS".
ENGLISH
Input mode display
One of these lights, depending on
the input signal.
• In the AUTO mode
INPUT
AUTO PCM DTS
DIGITAL ANALOG
• In the DIGITAL PCM mode
INPUT
AUTO PCM DTS DIGITAL
• In the DIGITAL DTS mode
INPUT
DIGITAL
AUTO PCM DTS
• In the ANALOG mode
INPUT
AUTO ANALOG
PCM DTS
Input signal display
• DOLBY DIGITAL
SIGNAL
DIGITAL
• DTS
SIGNAL
DIGITAL
• PCM
SIGNAL
DIGITAL
The indicator lights when digital signals
DIGITAL
are being input properly. If the indicator
DIGITAL
does not light, check whether the digital input
component setup (page 14) and connections are
correct and whether the component's power is
turned on.
NOTE:
• The indicator will light when playing
DIGITAL
CD-ROMs containing data other than audio
signals, but no sound will be heard.
23