Parts List - LUND SR2 Instrucciones De Instalación

PARTS LIST:

2 SR2 Running Boards
1 Driver/left side Front Mounting Bracket
1 Passenger/right side Front Mounting Bracket
2 Driver/left side Center/Rear Brackets
2 Passenger/right side Center/Rear Brackets
6 8mm Bolt/Nut Plates
6 8mm Double Bolt Plates
6 8mm Plastic Retainers
12 8-1.25mm x 30 Hex Bolts
(6) 8mm Bolt/Nut Plates
Passenger side
Center/Rear Brackets
Passenger side
Front Bracket
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.
2. Starting at the passenger front side of the vehicle, remove the sealing tape covering the factory holes in
the side of the inner panel, (Figure 1).
3. Determine the correct procedure to attach the passenger side Front Bracket for your model/year:
Models without factory threaded inserts in body panel, (see Figure 1):
a. Select (1) 8mm Bolt-Nut Plate, (Figure 2). Partially thread an 8mm Hex Bolt into the threaded nut
on the Bolt-Nut Plate, (Figure 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the
Hex Bolt as a handle and insert the Bolt-Nut Plate into the oval hole, (Figure 4). Feed the threaded
bolt on the Bolt-Nut Plate through one of the hex shaped factory holes.
b. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel,
(Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt-Nut Plate from falling into the
body panel and to aid in Bracket installation.
c. Select the passenger side Front Bracket, (Figure 6). Attach the Bracket to the threaded end of the
Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Nut, (Figure 7).
d. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 3a. Rotate the Bolt on the Bolt-
Nut Plate until the threaded nut lines up with the remaining hole in the Bracket and hex hole in the
body panel, (Figure 7). Attach the Bracket to the threaded nut with (1) 8mm x 30mm Hex Bolt, (1)
8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Do not tighten hardware.
Models with factory threaded inserts, (see Figure 8):
a. Attach the passenger side Front Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts,
(2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 8 & 9). Leave hardware loose.
09-17 DODGE RAM 1500 & 10-17 RAM 25-3500 CREW CAB
24 8mm x 24mm x 2mm Flat Washers
12 8mm Lock Washers
6 8-1.25mm Hex Nuts
12 8-1.25mm Nylon Lock Nuts
12 6-1.0mm x 25mm Button Head Bolts
24 6mm x 18mm x 1.6mm Flat Washers
12 6-1.0mm Flange Nuts
1 Allen Wrench
(6) 8mm Double
Bolt Plates
NOTE: Notch on
Front Brackets
Page 1 of 6
SR2 RUNNING BOARD
(6) 8mm Plastic
Retainers
Driver side
Front Bracket
Driver side
Center/Rear
Brackets
11/27/17 (RA)