Humidity Control; Automatic Defrosting - WOOD'S WCD2 Pro Manual De Instrucciones

DRAINAGE OF WATER
The dehumidifier is fitted with a hose
connection. By attaching a hose to the
dehumidifier the condensed water can be
drained directly away.
Using the hose:
1. Disconnect the dehumidifier from the
power source and remove the water
reservoir to give access to the drip tray.
2. Attach the hose coupling to the thread on
the dehumidifier and lead the hose to a
drainage outlet. Check that the hose is not
above the level of the drip tray.
3. Connect the dehumidifier to the power
source.
Without hose, direct to a drain outlet:
1. Disconnect the dehumidifier from the
power source and remove the water
reservoir.
2. Place the dehumidifier directly over the
drain so that the dehumidified water can
drip through the hole at the base of the
dehumidifier and into the drain.
3. Connect the dehumidifier to the power
source.

HUMIDITY CONTROL

Wood's dehumidifier is fitted with a built
in humidity control, which is set to the
desired level of humidity. The control
registers the current level of humidity and
ensures that the dehumidifier is turned on
and off automatically.
How to set the humidity control:
1. Set the humidity control knob to the
maximum position.
2. Set the fan to position II .
3. When the desired level of humidity is
reached, the hygrostat knob is turned
counterclockwise until the dehumidifier is
turned off.
10
NOTE: The ambient relative
humidity is most simply measured
with a Wood's hygrometer, and the most
suitable range is between 50% and 60%.
SHUTTING OFF AUTOMATICALLY
When the water reservoir is full, the
dehumidifier is shut off automatically.
The indicator light at the front of the
dehumidifier will switch to red to show
that the water reservoir should be
emptied.
1. Disconnect the dehumidifier from the
power source.
2. Empty the water reservoir.
3. Put the empty water reservoir back and
check that the float moves freely. See the
section on the Float.
4. Connect the dehumidifier to the power
source.
THE AIR FILTER
The air filter at the rear of the
dehumidifier ensures that the cooling
coils are kept free from dust. It is
important that the filter is kept clean
so that air can flow freely through the
dehumidifier.
Your dehumidifier is equipped with
a washable-filter that enhances the
capacity of the dehumidifier and cleanses
the air further. Please refer to the
separate filter leaflet for installation and
maintenance instructions.

AUTOMATIC DEFROSTING

Wood's dehumidifiers are fitted with
a control unit which ensures that the
cooling coils are defrosted automatically
when needed. The control shuts down
the compressor, which causes the cooling
of the coils to stop. The fan continues
to draw the air at room temperature
through the dehumidifier and thus melts
the ice, and the water runs down into
the reservoir. This defrosting system
means that the dehumidifier works at
temperatures as low as +2˚C.
Operating Instructions
FAN
The fan ensures that air flows through the
dehumidifier. Moist air is sucked in from
the rear and goes via the cooling coil and
the vaporizer to come out dry and warm
at the front of the dehumidifier. Wood's
dehumidifiers are fitted with two fan
speeds.
• Position II – gives a high air flow with
maximum dehumidifying of air.
• Position I – gives a lower air flow
which causes quieter operation and
somewhat lower dehumidifying
capacity.
ACCESSORIES
The dehumidifiers in WCD-series (WCD2,
WCD3 and WCD4) can be equipped with
an external water pump to drain the
condensate water. This is an accessory
and it is sold separately.
The dehumidifiers in WCD-series (WCD2,
WCD3 and WCD4) can be equipped with
a F8 filter which is efficient to capture
silica dust. When using a F8 filter it
should be replaced regularly (when full)
and not cleaned. You can contact your
reseller for further usage instructions and
replacement cycles. This is an accessory
and it is sold separately.
GB
11