2-Outlet Indoor Digital Timer Instruction Manual & Warranty
Read the following instructions carefully before using Timer.
Features:
•
Dual outlets – independent control for two different
outlets with a single keyboard and digital display.
•
7-Day programming – different ON/OFF times each day of
week. Up to 20 different ON/OFF settings.
•
Random or up-to-minute programming.
•
Easy to install, plug in to single Power source.
•
Random ON/OFF settings to make residence appear
occupied.
•
Battery backup – keeps program settings up to 1 year
even during power outages. Can be programmed without
being plugged in.
•
Manual override key – temporarily or permanently
overrides current program.
•
Random Setting- advanced feature automatically turns
lights on and off at randomly selected times.
Setting Procedure:
•
SET/TIME: to set the current time
•
[ + ] or [ – ]: Increase or Decrease time setting
•
RND: Press Random ON/OFF setting to activate random
delay for start or finish of ON periods.
•
RESET: To reset, press reset key with pointed object, i.e.
pencil. (Reset Timer before programming first time.)
•
CTD: Countdown indicates time left before appliance is
turned off.
•
MODE: Manual/Auto override
If programming is interrupted for more than 30 seconds while
setting Timer, unit will automatically revert to default mode.
Preset time will be preserved.
Setting Time:
If display does not appear, plug unit into wall receptacle and
charge battery for 1 hour.
1.
Remove unit from wall to begin programming.
2.
To select 12 or 24 hour clock press and hold TIME key for
around 3 seconds. Release the time key when AM is in
lower right corner to select 12 hour clock. No AM in the
corner indicates 24 hour clock.
3.
Press and hold SET key for around 3 seconds until "Mo"
display begins flashing. Press [ + ] or [ – ] keys to select
current day and press the SET key to confirm the Day
selection.
4.
The hour display will begin flashing. Press the [ + ] or [ –
] key to select hour. (Note AM or PM for twelve hour clock)
Press the SET key to confirm the selection.
5.
The minute display will start flashing. Press [ + ] or [ – ]
keys to select minutes and press SET key to confirm
minute selection.
6.
Time is now set.
For example ,the below display is Wednesday 3:12 AM
Programming On/Off Settings (maximum 20events)
1.
Clock time must be set before programming ON/OFF
times.
2.
After clock has been set, press [ + ] key. Display will look
as shown below. " PROG " " 1 " " A ON " " ON B " this is
the default setting for outlet A and B in Program 1. If you
want the default setting press SET key to confirm selec-
tion and go to step 4.
3.
If you want to select the desired output;
Press A if you want to program outlet A only ,the display
will look as below;
Press B if you want to program outlet B only ,the display
will look as below
Press and release A and B simultaneously to select both
outlet A and B (default setting above), Once the desired
output combination is displayed press SET key to confirm
selected output options.
4.
Use [ + ] or [ – ] keys and select block of days.
Options are:
-MO TU WE TH FR SA SU
-Individual day of the week
-MO TU WE TH FR (Weekdays only)
-SA SU (Weekends only)
-TH FR SA
-MO TU WE
-TU TH SA
-MO WE FR
press B key to confirm selection
5.
Select hour, using [ + ] or [ – ] keys. Press SET key to
confirm selection.
6.
Select minute, using [ + ] or [ – ] keys.press SET key to
confirm selection.
7.
Press [ + ] key to start PROG1 OFF setting selection.
NOTE:The output selection that is made for each PROG
ON will be used in the PROG OFF for that same program
number.
8.
Repeat steps 4 thru 6 to set day(s) and time device
should turn OFF.
Note: In one event for ON/OFF setting ,you can not change
A/B selection.See 7 above.
9.
To set additional ON/OFF cycles, (maximum 20events),
press [ + ] key. Then press [ + ] or [ – ] keys and follow
procedures in steps 3 thru 8 for each new ON/OFF event.
10. When finished programming ON/OFF events, press TIME
key. Display will show current time.
Deleting Programs
1.
Press [ + ] key. Use [ + ] or [ – ] keys to select ON/OFF
event to be deleted.
2.
Press SET key to select event. Press MODE key to delete
program setting.
Note: in step 2 ,press MODE again to recover the settings
.After pressing MODE do not change the A/B/AB setting,
or it will make the setting recovery impossible3. When
done, press TIME key to return to current time and day.
Count Down On/Off Setting
1.
Press [ – ] key. Display will look as shown in Fig. 3,
indicating "CTD" and "PROG" to indicate programming of
Count Down Timer.
The default setting for the countdown timer (CTD) is both
outlets on. In the display you will see (A ON and ON B)
flashing
2. If you want the default setting press the SET key to select
A and B.
a. Use [ + ] or [ – ] keys select CTD AB hour(s).
b. Press SET key to confirm selection.
c. Use [ + ] or [ – ] keys to enter CTD AB minutes.
d. Press SET key to confirm selection.
e. Use [ + ] or [ – ] keys to enter CTD AB seconds.
f. Press SET key to confirm selection and go to STEP 4
OR.
3.
To select single A or B outputs press the selected button
A or B. In the display you will see A ON or ON B Flashing.
Press SET to confirm selection. The selected outputs will
stop flashing and remain on while the Count-down time is
set. The digits for hours will start flashing.
a. Use [ + ] or [ – ] keys select CTD A or B hour(s).
b. Press SET key to confirm selection.
c. Use [ + ] or [ – ] keys to enter CTD A or B minutes.
d. Press SET key to confirm selection.
e. Use [ + ] or [ – ] keys to enter CTD A or B seconds.
f. Press SET key to confirm selection.
g. Repeat step 3 to program the second output if desired
TE23WHB