Service; Optional Equipment - Jøtul F 100 Instrucciones Para Instalación En Informacion Tecnica

ENGLISH
Rear mounted fl ue pipe
If the fl ue pipe is to be rear mounted do the following:
• Cut out a hole in the heat shield at the back for the
fl ue pipe (fi g. 3).
• Unscrew the two screws holding the cover for the rear
outlet from the inside. (Hold the cover when removing
the last screw) (fi g. 5A).
• Fasten the cover on the top plate.
• Connect the smoke outlet to the rear plate.
• Install the ash lip by hanging it under the door.
• Screw the door knob on the handle. (Place the white
washer between the handle and the knob.)
• Remove the protective paper from the gasket and
fasten it around the outside of the fl ue pipe.
• Mount the fl ue pipe into the fl ue outlet.
N.B. It is important that the joints/fl ue pipes are completely
sealed. Air leaks can prevent the fl ue pipe from functioning
properly.
Top mounted fl ue pipe
If the fl ue pipe is to be top mounted do the following:
1. Attach the fl ue outlet to the top plate using the two screws.
Fig. 4A.
2. Install the ash lip by hanging it under the door.
3. Screw the door knob on the handle. (Place the white washer
between the handle and the knob.)
4. Remove the protective paper from the gasket and fasten it
around the outside of the fl ue pipe.
5. Mount the fl ue pipe into the fl ue outlet.
N.B. It is important that the joints/fl ue pipes are completely
sealed. Air leaks can prevent the fl ue pipe from functioning
properly.
3.6 Control of functions
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F 100 is equipped with the following controls:
Air vent: fi g. 2A
Ignition vent: fi g. 2B
To the left: Closed
To the right: Open
3.7 Ash removal (fi g 6)
Jøtul F 100 with ash pan
1. Open the grate.
2. Lift out the ash pan.
3. Carefully place the grate down.
4. Ideally, some ash should be left as a protective layer for the
bottom of the fi replace.
5. Make sure the door to the ash pan is securely shut when
the stove is in use.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
measures».
22
All manuals and user guides at all-guides.com
Jøtul F 100 without ash solution
1. Lift out the ash retainer
2. Use a shovel or similar and scrape out the ash.
3. Leave a little ash in the bottom of the combustion chamber
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
measures».

4.0 Service

Warning! Any unauthorised change to the product is illegal!
Only use original spare parts!
4.1 Replacement of the baffl e plate
– inner bottom – burn plates
1. Remove the ash retainer.
2. Lift the baffl e, which rests on the burn plates, forwards and
3. Lift up the inner bottom and tilt it out.
4. Remove the burn plates.
Follow the same procedure for installation, but in reverse.

5.0 Optional equipment

5.1 Floor plate
For the Jøtul F 100 we can supply a decorative blue-black
enamelled fl oor plate.
Size: 630 x 759 x 17 mm.
5.2 Long legs
If you would like a taller fi replace it is possible to install longer
legs. Height 215 mm.
5.3 Extra heat shield - Cat. no.
50012956
If the product is mounted with an extra heat shield, see fi g. 1
for distances from wall to
«6.1 Fire preventive
as a protective insulating layer.
to the side and then tilt it down and out of the door. (If the
product is rear-mounted the top plate may be lifted off and
the baffl e removed through the top.)
stove.
«6.1 Fire preventive