Technical Data - Milwaukee M12 FTB Manual Original

12

TECHNICAL DATA

Type
Production code
Battery voltage
Rated speed (Drilling)
Rated speed (Buffing)
Weight according EPTA-Procedure 01/2014
(Li-Ion 2,0 Ah ... 6,0 Ah)
Tool reception
Max Buffing Accessory Ø
Max Drilling Accessory Ø
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Noise information: Measured values determined according to
EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
Vibration information: Vibration total values (triaxial vector sum)
determined according to EN 60745.
Vibration emission value a / Uncertainty K
h
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
TYRE BUFFER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire Brushing
or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
b) Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure
safe operation.
c) The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
d) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool. Incorrectly
sized accessories cannot be adequately guarded or controlled.
e) The arbour size of wheels, sanding drums or any other
accessory must properly fit the spindle or collet of the power
tool. Accessories that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively and may
cause loss of control.
M12 FTB
Tyre Buffer
4830 13 01 XXXXXX MJJJJ
12 V
1200 min
-1
2500 min
-1
1,1 ... 1,3 kg
7/16" HEX (11 mm)
80 mm
9,5 mm
-18 ... +50 °C
M12B...
C12C; M12C4; M12-18...
64,6 dB (A) / 3 dB (A)
75,6 dB (A) / 3 dB (A)
< 2,5 m/s / 1,5 m/s
2 2
f) Mandrel mounted wheels, sanding drums, cutters or other
accessories must be fully inserted into the collet or chuck. If
the mandrel is insufficiently held and/or the overhang of the wheel is
too long, the mounted wheel may become loose and be ejected at
high velocity.
g) Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of
stopping flying debris generated by various operations. The dust
mask or respirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high intensity noise may
cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
equipment. Fragments of workpiece or of a broken accessory may
fly away and cause injury beyond immediate area of operation.
j) Hold the power tool by insulated gripping surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
ENGLISH
13