Tabla de contenido
Publicidad
Implementación MIDI
Modelo HPD-15
Versión 1.00
Marzo.23 2000
1. Recepción de información
Mensajes de Voz del Canal
* The following channel voice messages are received on the channel specified as the
[SYSTEM]-(MIDI).
Desactivación de Notas
Status
2nd byte
8nH
kkH
9nH
kkH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
kk = note number:
00H - 7FH (0 - 127)
vv = note off velocity:
01H - 7FH (1 - 127)
* In the melody parts, the velocity values of Note Off message are ignored.
* When the Trigger Mode of the pad is set to "Shot", the pad part and the percussion parts
will ignore the velocity values of Note Off message.
* When the Trigger Mode of the pad is set to "Gate" or "Trig", the pad part and the
percussion parts will receive only the note numbers which are specified by the patch,
and the same processing will be carried out as when pad is released.
* When recording, this is recorded in the sequencer data itself.
Activación de Notas
Status
2nd byte
9nH
kkH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
kk = note number:
00H - 7FH (0 - 127)
vv = note on velocity:
00H - 7FH (0 - 127)
* The pad part and the percussion parts will receive only the note numbers which are
specified by the patch.
* When recording, this is recorded in the sequencer data itself.
Pulsación de la Tecla Polifónica
Status
2nd byte
AnH
kkH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
kk = note number:
00H - 7FH (0 - 127)
vv = pressure:
00H - 7FH (0 - 127)
* Only the pad part and the percussion parts can be received.
* The pad part and the percussion parts will receive only the note numbers which are
specified by the patch.
* This is used as the pad pressure data.
* When recording, this is recorded in the sequencer data itself.
Cambio de Control
Bank Select (Controller number 0, 32)
Status
2nd byte
BnH
00H
BnH
20H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
mm = Bank number MSB:
00H - 02H (bank1:User Patch bank2,3: Preset Patch)
ll = Bank number LSB:
processed as 00H
* Only the pad part and the percussion parts can be received.
* Bank select processing will be suspended until a program change message is received.
* Not recorded in the sequencer.
3rd byte
vvH
00H
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Modulation (Controller number 1)
Status
2nd byte
BnH
01H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
* Only the pad part and the percussion parts can be received.
* This is used as the data of the [LFO PITCH] knob.
* When recording, this is recorded in the sequencer data itself.
Foot Control (Controller number 4)
Status
2nd byte
BnH
04H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
* Only the pad part the and percussion parts can be received.
* This is used as the position data of the pedal connected to the EXP PEDAL/HH CTRL
jack.
* When recording, this is recorded in the sequencer data itself.
Data Entry (Controller number 6)
Status
2nd byte
BnH
06H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
mm = The value of the parameter specified by RPN.
* Only the melody parts can be received.
* Not recorded in the sequencer.
On the normal mode of HPD-15, RPN can be used to modify the following parameters.
RPN
Data entry
MSB LSB
MSB LSB
00H 00H
mmH ---
7FH 7FH
--- ---
Volume (Controller number 7)
Status
2nd byte
BnH
07H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
* Only the percussion parts and the melody parts can be received.
* This is used as the part level of the sequencer pattern data.
* Not recorded in the sequencer.
Pan (Controller number 10)
Status
2nd byte
BnH
0AH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 40H - 7FH (Left - Center - Right)
* In the melody parts, it is used as the part panpot of the sequencer pattern data.
* In the pad part or the percussion parts, it is used as the data of the [PAN] knob.
* When recording, this is recorded in the sequencer data itself if it is received on the pad
part or the percussion parts.
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
Explanation
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
LSB: ignored (processed as 00H)
specify up to 2 octaves in semitone steps
RPN null
set condition where RPN is unspecified. The data
entry messages after set RPN null will be
ignored. (No Data entry messages are required
after RPN null).
Settings already made will not change.
MSB,LSB of data entry: ignored
3rd byte
vvH
3rd byte
vvH
91
Publicidad
Capítulos
Tabla de contenido
