Additional Safety Rules - Makita 9032 Manual De Instrucciones

ENGLISH
1 Lock lever
2 Arm
3 "A" range
4 Screw
5 Lock button
6 Switch trigger
7 Speed adjusting dial
SPECIFICATION
Model
Belt size .................................................. 9 mm x 533 mm
Belt speed................................................... 5 m – 28 m/s.
Overall length ...................................................... 420 mm
Net weight .............................................................. 1.5 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
2. Hold the tool firmly with both hands.
3. Make sure the belt is not contacting the work-
piece before the switch is turned on.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. This tool has not been waterproofed, so do not
use water on the workpiece surface.
7. Ventilate your work area adequately when you
perform sanding operations.
8. Some material contains chemicals which may be
toxic. Take caution to prevent working dust inha-
lation and skin contact. Follow material supplier
safety data.
9. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
Explanation of general view
8 Cam lever
9 Rear pulley
10 Abrasive belt
11 Adjusting dial
12 Dust nozzle
13 Hose 28
14 Hose for vacuum cleaner
OPERATING INSTRUCTIONS
9032
Adjusting arm inclination (Fig. 1)
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting the arm inclination.
The arm can be pivoted and fixed at any desired angle
within the "A" range according to the operating position or
the figure of the workpiece.
Loosen the lock lever by raising it. Pivot the arm to the
desired position, and secure the lock lever to fix the arm
firmly.
Replacing arm (Fig. 2)
CAUTION:
Always be sure that the tool is switched off and
unplugged before replacing the arm.
By replacing the standard-equipped arm by optional one,
6 mm or 13 mm width belt can be used. Remove the arm
by loosening the screw that secures the arm. Insert the
arm that fits the belt to be used, and tighten the screw
firmly.
Switch action (Fig. 3)
ENB007-2
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop. For continuous operation, pull
the switch trigger and then push in the lock button. To
stop the tool from the locked position, pull the switch trig-
ger fully, then release it.
Speed adjusting dial (Fig. 4)
The belt speed can be infinitely adjusted between 5 m
and 28 m per second by turning the speed adjusting dial
to a given number setting from 1 to 6.
Higher speed is obtained when the dial is turned in the
direction of number 6; lower speed is obtained when it is
turned in the direction of number 1. Select the proper
speed for the workpiece to be sanded.
CAUTION:
The speed adjusting dial can be turned only as far as 6
and back to 1. Do not force it past 6 or 1, or the speed
adjusting function may no longer work.
15 Vacuum cleaner
16 Dust collector
17 Flat shoe
18 Limit mark
19 Brush holder cap
20 Screwdriver
5