Mounting Dimensions - Airwell HDLA-025N-09M25 / YDAA-025H-09M25 Manual De Instrucciones

Outdoor Unit Dimensions (mm)
681x434x285 (26.8"x 17.1"x 11.2") 460 (18.1")
700x550x270 (27.5"x 21.6"x 10.6") 450 (17.7")
700x550x275 (27.5"x 21.6"x 10.8")
YDAA-025H-09M25
720x495x270 (28.3"x 19.5"x 10.6")
YDAA-035H-09M25
728x555x300 (28.7"x 21.8"x 11.8")
765x555x303 (30.1"x 21.8"x 11.9")
770x555x300 (30.3"x 21.8"x 11.8") 487 (19.2")
YDAA-050H-09M25
805x554x330 (31.7"x 21.8"x 12.9") 511 (20.1")
800x554x333 (31.5"x 21.8"x 13.1") 514 (20.2")
845x702x363 (33.3"x 27.6"x 14.3")
890x673x342 (35.0"x 26.5"x 13.5")
YDAA-070H-09M25
946x810x420 (37.2"x 31.9"x 16.5")
946x810x410 (37.2"x 31.9"x 16.1") 673 (26.5")
If you will install the unit on the ground or
on a concrete mounting platform, do the
following:
1. Mark the positions for four expansion bolts
based on dimensions chart.
2. Pre-drill holes for expansion bolts.
3. Place a nut on the end of each expansion bolt.
4. Hammer expansion bolts into the pre-drilled
holes.
5. Remove the nuts from expansion bolts, and
place outdoor unit on bolts.
6. Put washer on each expansion bolt, then
replace the nuts.
7. Using a wrench, tighten each nut until snug.
WARNING
WHEN DRILLING INTO CONCRETE, EYE
PROTECTION IS RECOMMENDED AT ALL
TIMES.
Page 27
 
W x H x D

Mounting Dimensions

Distance A (mm)
450 (17.7")
452 (17.8")
452 (17.8")
452 (17.8")
540 (21.3")
663 (26.1")
673 (26.5")
If you will install the unit on a wall-mounted
bracket , do the following:
CAUTION
Make sure that the wall is made of solid brick,
concrete, or of similarly strong material. The
wall must be able to support at least four
times the weight of the unit.
1.Mark the position of bracket holes based on
dimensions chart.
2. Pre-drill the holes for the expansion bolts.
3. Place a washer and nut on the end of each
expansion bolt.
4. Thread expansion bolts through holes in
mounting brackets, put mounting brackets
in position, and hammer expansion bolts into
the wall.
5. Check that the mounting brackets are level.
6. Carefully lift unit and place its mounting feet
on brackets.
7. Bolt the unit firmly to the brackets.
8. If allowed, install the unit with rubber
gaskets to reduce vibrations and noise.
Distance B (mm)
292 (11.5")
260 (10.2")
260 (10.2")
255 (10.0")
302(11.9")
286(11.3")
298 (11.7")
317 (12.5")
340 (13.4")
350 (13.8")
354 (13.9")
403 (15.9")
403 (15.9")