Bluetooth Connectivity; Disconnect From A Device; App Features - Bowers & Wilkins PI7 Manual De Instrucciones

6. Bluetooth Connectivity

6.1 Pairing
Your PI7 earphones are designed to stream music
wirelessly from Bluetooth audio devices, such as
smartphones, tablets, or computers. To do so, the
earphones and device must first be paired.
When you receive your PI7 earphones they will be
ready to pair to any Bluetooth audio device.
6.1.1 iOS System / Android System without
Google FastPair.
1. Download the Bowers & Wilkins
Headphone App.
2. Open the case lid, the case indicator will
flash blue.
3. Go to the Bluetooth pairing menu of your
device and select the "Bowers & Wilkins PI7"
from the device list.
4. The case indicator will change to solid blue to
indicate pairing is successful.
5. Open the Bowers & Wilkins app and add the
headphones.
Note: Your earphones will automatically exit
Bluetooth pairing mode if no device is paired
within 5 minutes. If pairing fails, the indicator will
rapid flash blue, please try pairing again.
To pair to a subsequent device. See Diagram 5:
1. Open the case lid with the earbuds placed
inside the case.
2. Press and hold the button inside the case for
between 1 and 5 seconds, the case indicator
will flash blue.
3. Go to the Bluetooth pairing menu of your new
device and select the "Bowers & Wilkins PI7"
from the device list.
4. The case indicator will change to solid blue to
indicate pairing is successful.
PI7 can remember up to 3 paired Bluetooth Devices.
Repeat the above steps to pair more devices.
Note: Your earbuds will automatically exit
Bluetooth pairing mode if no device is paired
within 5 minutes. If pairing fails, the indicator will
rapid flash blue, please try pairing again.
6.1.2 Google FastPair (For Android System
integrated with GFP Feature)
To add your headphones:
1. Place the case no further than 10cm (4 inches)
away from Android device (BT enabled) and
open the PI7 case lid.
2. A GFP (Google FastPair) notification window
will pop up showing "Bowers & Wilkins PI7
detected" and request to start the pairing
process.
3. Press "Notification" button on the window to
enable the pairing, successful connection will
be shown in GFP window.
4. Once paired:
o GFP window will direct you to the Google
Play store to download and Install the
Bowers & Wilkins App.
o L/R Earbud and case Battery Level can be
seen on the GFP window

6.2 Disconnect from a Device

You can quickly disconnect PI7 from a device by
putting the earbuds back to the case. Alternatively,
you can manage connection in further detail using
the Bowers & Wilkins Headphones app under
Connections.
Diagram 5
Bluetooth pairing - subsequent device

6.3 App features

The Bowers & Wilkins Headphones app provides
extended setup and adjustments to features such
as Adaptive Noise Cancellation, Ambient Pass-
Through, and Wear Sensors. The app also provides
further customisations such as voice prompt, level
of ambient pass-through, connection management,
and headphone software updates. The app is
available as a free download on iOS and Android
devices.
To add your headphones:
1. From your mobile device, download and install
the Bowers & Wilkins Headphones app.
2. Launch the app, then read and follow the
instructions pertaining app notification and
permissions.
3. After reaching the main screen, simply tap +
and following the in-app instructions.
6.4 Headphone Software Update
Bowers & Wilkins will occasionally make available
software updates that refine and optimise the
performance of your headphones or add new
features.
The Bowers & Wilkins Headphones app will notify
you when a software update is available, tap on the
notification and follow the in-app instructions.
5