Speci Cations - Audio-Technica AT-LP5 Manual De Instrucciones

Troubleshooting
Turntable operates but emits no sound or not enough sound.
1. Ampli er (system) controls are set incorrectly: wrong input selected,
tape monitor on, speakers switched off, etc. Verify proper control
settings.
2. Stylus is broken or missing. Check the stylus assembly and replace if
necessary.
3. The stylus assembly may not be fully seated in the cartridge body. Check
the cartridge and adjust if necessary.
4. The pre-ampli er selector switch of the AT-LP5 is set in the wrong
position. Verify that it is set to the correct output to match ampli er
input.
- No sound/very weak sound: Phono Out setting into an Aux/Line input.
- Very loud/distorted sound: Line Out setting into a Phono input.
5. The tracking force is set too heavy (stylus assembly is bottoming out on
record). Set tracking force per cartridge manufacturer's recommenda-
tion.
6. Turntable is picking up excessive vibrations from oor, walls, or nearby
speakers. Reduce vibrations or place turntable on sturdy/solid surface.
Turntable operates but stylus "skips" across record.
1. The stylus guard is still in place. Remove the stylus guard.
2. The tracking force is set too light. Set tracking force per cartridge
manufacturer's recommendation.
3. The anti-skate control is set improperly. Verify anti-skate is set for
same value as cartridge tracking force.
Record sounds too fast or too slow.
1. Turntable is set for wrong speed. Make proper speed selection for
record type being played with platter speed selector.
Tips to avoid damage
• Do not touch the stylus tip with your ngers; avoid bumping the stylus
on the turntable mat or a record's edge.
• Clean the stylus tip frequently, using a soft brush and a
back-to-front motion.
• If you use a stylus cleaning uid, use it sparingly.
• Never apply harsh chemicals or solvents to any part of the turntable
system.
• Prior to moving the turntable, always unplug it from the AC outlet and
lock the tonearm on the tonearm rest.

Speci cations*

Turntable Speci cations
Type
Motor
Drive method
Speeds
Turntable platter
Starting torque
Braking system
Wow and utter
Signal-to-noise ratio
Outputs levels
"PHONO" (Pre-amp bypassed)
"LINE" (Pre-amp engaged)
Phono Pre-amp gain
USB function
A/D, D/A
Computer interface
Tonearm Speci cations
Type
Effective length
Overhang
Maximum tracking error angle
Stylus pressure adjustment range
Applicable cartridge weight
range (including headshell)
Cartridge and Headshell Speci cations
Cartridge Model
Cartridge Type
Recommended load impedance
Output voltage
Stylus
Tracking force range
Cartridge weight
Headshell model
Headshell weight
Headshell overhang adjustment
General Speci cations
Power supply requirements
Power consumption
Dimensions
Weight
Accessories included
Audacity :
System requirements
Installation
*Speci cations are subject to change without notice.
2-Speed, fully manual operation
DC motor
Direct drive
33-1/3 RPM, 45 RPM
Die-cast aluminium
>1.6 kgf.cm
Electronic brake
< 0.2% WRMS (33 RPM)
> 50 dB
3.5 mV nominal at 1 kHz, 5 cm/sec
150 mV nominal at 1 kHz, 5 cm/sec
36 dB nominal, RIAA equalized
16 bit 44.1 kHz or 48 kHz USB selectable
USB 2.0 Compliant Windows XP, Vista or
MAC OSX
Static balance J-shaped tonearm
247 mm
17 mm
Less than 2.5°
0 to 2.5 g
15 to 20g
AT95EX
VM Design Stereo Dual Moving Magnet
47,000 Ohms
3.5 mV (at 1 kHz, 5 cm/sec)
0.3 x 0.7 mil elliptical
1.5 to 2.5 g (standard 2 g)
(AT95Ex) 5.7 g
AT-HS10
10 g
± 5 mm
220 to 240 V AC, 50/60 Hz
6W
450.0 mm (17.72") W x 352.0 mm
(13.86") D x 157.0 mm (6.1") H
8.5 kg (18.74 lbs)
AT95EX Dual Moving Magnet stereo
cartridge with replaceable stylus;
Exclusive AT-HS10 Lightweight
Headshell; AC line cord; dual RCA (male)
to dual RCA (male) stereo cable; 45 RPM
adapter; USB cable; recording software
PC or Mac with an available USB port
(USB2.0 or higher)
Mac running OS X 10.4 to 10.10 or PC
running Windows (XP and above)
CD-R or CD-RW writer for burning CDs
& software installation
Includes Audacity software for PC &
Mac users
7