SISTEMA TR2TSS Manual De Instrucciones página 4

Handle assembly
A1
Water inlet
A
Water outlet
B
On/off switch
C
Electric wire
D
Gun and hose
E
AVVIAMENTO
STARTING-UP
Warning: Before start-up please read carefully the
instructions.
Turn the starting switch into the "0" position. Connect the
1
high pressure hose to the delivery pipe OUTLET. Connect the
water hose to the INLET. The presence of red dust in the
connections is normal and does not interfere with the use
and functioning of the machine.
Always use the filter supplied. Sand, limestone and furrings
2
damage the pump valves. Priming soiled water invalidates the
warranty !
Open the water tap completely. The limit of the incoming
3
water temperature has to be 40°C.
Connect the plug to the socket. Press the gun lever so that
4
air and possible pressure residues come out from the pipes.
Keeping the gun lever pressed, switch on the device
5
by setting the switch to "I".
Lance assembly. USE ALWAYS THE LANCE EXTENSION.
6
Do not use the nozzle on the gun directly.
At the end of work: a) switch off the cleaner; b) disconnect
7
the water mains; c) discharge the water inside the pump and
high pressure pipe, leaving the gun open for a few seconds.
This reduces the risk of scale formation and will facilitate the
new electro-pump starting.
USAGE
8 High pressure nozzle adjustment.
Gun safety device.
9
10 Use of detergent spray attachment.Use only biodegradable soap.
11
The output water pressure is adjustable and it is controlled
by the lever.
TURBO NOZZLE VORTEX Nozzle and rotating jet to
12
increase the washing effect (the turbo lance is not adjustable).
WARNING
7
Before start up always operate the machine without the lance.
15
The washer is supplied with lubrication close system, so no
addition of oil is needed.
16 To lubricate the o-rings use "GREASE FOR BEARINGS".
Uncoupling of the handle: spread out the plastic couplings,
17
protruding the handle.
Warning: High pressure hoses, fittings and couplings
are important for the safety of the appliance.
Use only hoses, fittings and couplings recommended by
All manuals and user guides at all-guides.com
F Lance
Extension
G
H Detergent spraying attachment
Vortex
I
L Fixed brush
(model with fixed brush only)
Rotating brush
M
(model with rotating
brush only)
GB
the manufacturer.
Only for the model provided with Total Stop System (TSS):
the pressure washer is equipped with a stop device which will
sense when the trigger on the gun is released. It will open the
power circuit to the motor and cause the pressure washer to stop.
Remember not to use the TSS as a main switch.
ATTENTION: There are two slots in the front plastic cover
where the electrical cable could be put in. One slot, the big-
gest one, is only for the H07RN-F cable, the other one is for
the H05RN-F or for the H05VV-F cable. Follow the written
indications on the internal part of the plastic cover.
NOZZLE CLEANING if the water jet is not regular during the
functioning or the thermic safety switch switches off the machine,
the nozzle is likely to be blocked. Proceed as follows:
1. Remove plug from power socket.
2. High pressure can cause serious injury. Keep spray head
well clear of the face, other people, animals or plants.
Protective clothing and goggles must be worn during use.
3. Remove lance from the gun.
4. Using the tool provided, remove dirt from the hole in the
spray head and rinse well.
5. Perform a visual check through the nozzle to see if all
obstacles are removed.
SPRAY HEAD CLEANING TOOL
ALWAYS USE THE FILTER SUPPLIED
Clean the filter Inspect periodically the suction filter in order to
avoid obstruction and damage to the machine working.
Sand, limestone and furrings damage the pump valves.
Priming soiled water invalidates the warranty !
PLEASE READ THE MANUAL
"SAFETY INSTRUCTIONS"
4
A
B
2