Remote Controller - camry Premium CR 7853 Manual De Uso

WARNING:
When operating the device in conditions of varying humidity, the down cooler drain hole (9) should be constantly open and ensure
constant water drainage. To comfortable draining the water use included plastic pipe.
COOL "K" mode:
1. When the room temperature is higher than set temperature on control panel, the compressor starts to run.
2. When the room temperature is lower than set temperature on control panel, the compressor stop and upper fan operates at
original set speed.
Fan "M." mode:
1. The upper centrifugal fan runs at set speed, and the compressor does not run.
2. The adjustment of temperature is no effective.
Heat "R" mode:
1.When the room temperature is higher than the set temperature, the device will stop heating function automatically.
2.When the room temperature is lower than set temperature, the device will start heating function automatically.
Timer operation "N":
1. Press "N" button to set Automatic Off time while the unit is running.
2. Press "N" button to set Automatic On time while the unit is ready status.
3. The time can be adjusted within a range of 1 hour to 24 hours by pressing the button "D" to increaseor "E" to decrease the period
of the device operation.
Sleep mode "I" operation
1. The sleep mode operations when the unit is under cooling "K" mode and heating "R" mode.
2. Press the button "I" in cool mode "K" , then the unit will work under sleep mode and the upper centrifugal fan will turn to low
speed automatically. The set temperature will increase by 1 ℃ after one hour, and increase 2℃ after two hours. After six hours the
unit will stop running.
3. Press the button "I" in heating mode "R" , then the device will work under sleep mode and the up centrifugal fan will turn to low
speed automatically. The set temperature will decrease by 1 ℃ after one hour, and decrease 2℃ after two hours. After six hours the
unit will stop running.
Swing "O" mode operation:
When the device is on, press button "O" , the vertical louver will on or off. When swing mode is on, the louver can swing up and
down within 60 degree. Press the button "O" again, the louver will stop swinging.
WI-FI function - Connection
Please note that the appearance of the screenshots shown on page 4 may be changed by "Tuya Smart" as a result of technological
development from the date of production of the product to the date of purchase of this device, however, the general principle of
connection is described below:
1. Download Application "Tuya Smart" on your smart phone.
2. Then "add device". Look at print screen I.
3. Press icon of folder "Large home appliances".
4. Press icon of folder "Portable Air Conditioners (WI-FI)". Look at print screen II.
5. Choose "2,4G Hz Wi-Fi" (password field is blank, write your password) press "Next". Look at print screen III.
6. At screen: "Reset the device at first" press "Confirm the indicator is blinking rapidly" and press "NEXT". Look at print
screen IV.
Warning: If at your device the Wi-Fi indicator "T" is not blinking rapidly, please do set the device under stand-up and please do hold
the timer / temperature up button "D" for seconds, then WI-FI lamp will blink.
7. Now you see "Addling device" screen and progress of adding device process. It takes just few seconds.
8. When you see "Added successfully" press "Done". Look at print screen V.
9. You see screen "Welcome Home", then you should press icon switch off "OFF" to change into switch on "ON" to start
operation same way as it is described for operation via remote controller (4).
Notice:
The main control board has memory function, when the device is ready to run but in stop status, the main control board can
memorize the initialization of working mode. When you turn on the unit, it will work as the same enactment of working-mode as last
time, no need to reset the working mode again. (This condition is not available when the unit is under AUTO mode "J".)

REMOTE CONTROLLER

1. Slide the back cover to open and take off the isolating film on the batteries.
7