Dehumidifying (Dry); Fan Only; Adjusting The Fan Speed; Night Mode - Argo Ulisse 10 A Instrucciones De Uso

Acondicionador de ambiente con condensador a distancia
Ocultar thumbs Ver también para Ulisse 10 A:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 50

DEHUMIDIFYING (DRY)

1. Set the MODE button to DRY. The icon
2. Press the ON/OFF button and switch the air condioner ON.
3. Press the TEMP. buttons to set the desired temperature (the
temperature range is between 32 °C max. and 16 °C min.).
THE DISPLAY SHOWS THE SELECTED
TEMPERATURE.
NOTE
Use DRY operation when you want to reduce the humidity in
the room.
● Once the room temperature reaches the set level, the unit
repeats the cycle of turning on and off automatically.
● During DRY operation, the fan speed is automatically set
to
or stops to prevent overcooling.
● Dry operation is not possible if the indoor temperature is 15
°C or less.

FAN ONLY

If you want to make air circulate without any temperature control,
follow these steps:
1. Press the ON/OFF operation button and switch the air
conditioner ON.
2. Press MODE button until only the
the display.

ADJUSTING THE FAN SPEED

AUTOMATIC
Simply set the FAN selector to the
microcomputer automatically controls the fan speed when
the AUTO mode is selected. When the air conditioner starts
operating, the difference between the room temperature
and the set temperature is detected by the microcomputer
which then automatically switches the fan speed to the
most suitable level.
WHEN DIFFERENCE BETWEEN
ROOM TEMPERATURE AND SET
TEMPERATURE IS
Cooling and
2 °C and over
dehumidifying
Between 2 and 1 °C
modes:
Below 1 °C
2 °C and over
Heating mode:
Below 2 °C
is displayed.
AFTER 5 SECONDS FROM THE REQUIRED
TEMPERATURE SETTING THE DISPLAY WILL
SHOW THE ROOM TEMPERATURE AGAIN.
fan sign appears on
position.A
FAN SPEED
High
Medium
Low
High
Medium
NOTE
The above mentioned data make reference to the
conditioner operating when the sensor on the remote control
unit is ON. (Refer to temperature sensor selector). If the
sensor on the indoor unit is being used then actual operation
will slightly differ from that described in the above tables.
The automatic speed is not active in FAN ONLY mode.
MANUAL
If you want to manually adjust speed just set the FAN selector
as desired.
High speed

NIGHT MODE

The NIGHT mode enables you to save energy.
1. Set the MODE selector to cool, dry or heat.
2. Press the NIGHT button.
3. The
mark appears on the display. Press the NIGHT
button again to release the NIGHT function.
What does the NIGHT mode mean?
In this mode, the air conditioner will cool or heat the room
to the set temperature, and then the thermostat will make
the unit pause. After about 1 hour, the air conditioner will
automatically reset the set temperature as follows (also
refer to graphs).
OPERATING MODE
Heating
Cooling and Dehumidifying
When the room temperature reaches the new set value,
the thermostat will cause the unit to pause. After about 1
hour the temperature will be raised by 1 °C in cooling, or
lowered by 1 °C in heating. This enables you to save energy
without sacrificing your comfort.
COOLING AND DEHUMIDIFYING
Setting temperature Room temperature
1°C
1°C
1 hour 1 hour
TIME
Setting temperature
9
Med. speed
Low speed
SET TEMPERATURE CHANGE
Lowered by 1 °C
Raised by 1 °C
HEATING
Room temperature
1°C
1°C
1 hour
1 hour TIME
EG

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ulisse 13 aUlisse hlaOscar twin 11aOscar twin 14a

Tabla de contenido