Manufacturer's Warranty; Spare Parts Lists - REMS Power-Press SE Instrucciones De Servicio

g
Wrong pressing tongs, Mini pressing tongs, pressing ring (pressing contour,
size) or adapter tongs inserted.
Pressing tongs, Mini pressing tongs, pressing ring or adapter tongs stiff or
defective.
5.3. Fault: REMS Power-Press SE switches of repeatedly at the end of the pressing.
Cause:
Defective drive unit.
5.4. Fault:
Cause:
Damaged or worn pressing tongs, Mini pressing tongs, pressing ring,
pressing segments or pressing contour.
Wrong pressing tongs, Mini pressing tongs, pressing ring (pressing contour,
size) or adapter tongs inserted.
5.5. Fault: Pressing jaws close without load on the pressing tongs, Mini pressing tongs offset at "A" and "B" (Fig. 1).
Cause:
bent.
5.6. Fault:
Cause:
Expansion too long.
5.7. Fault:
Cause:
5.5.
Wrong compression head (compression sleeve system, size) used.
Battery depleted or defective (REMS cordless drive units).
Drive unit defective.
5.8. Fault: Expander does not complete the expanding, expanding head does not open fully.
Cause:
Drive unit overheated (REMS Power-Ex-Press Q & E ACC).
Worn carbon brushes (REMS Power-Ex-Press Q & E ACC).
Battery depleted or defective (REMS cordless drive units).
Drive unit defective.
Expanding head stiff or defective.
Expander set incorrectly (REMS Akku-Ex-Press Cu ACC).
6. Disposal
The drive units, batteries and rapid chargers may not be thrown in he household

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
original purchase documents, which must include the date of purchase and the
designation of he product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference in an unassembled condition. Replaced products and parts
shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of the user, in particular the right to make claims against the
Check the labelling on the pressing tongs, Mini pressing tongs, pressing ring or
adapter tongs and change if necessary.
Do not use the pressing tongs, Mini pressing tongs, pressing ring or adapter
tongs any further! Clean and lightly grease the pressing tongs, Mini pressing
tongs, adapter tongs with machine oil or replace them with new ones.
Have it checked/repaired by an authorised REMS customer service workshop.
Replace the pressing tongs, Mini pressing tongs, pressing ring with new ones.
Check the labelling on the pressing tongs, Mini pressing tongs, pressing ring or
adapter tongs and change if necessary.
the installation and assembly instructions of the manufacturer/supplier of the
Send he pressing tongs, Mini pressing tongs to an authorised REMS customer
service workshop for inspection.
Check whether the right expanding head was used. Pipe expanded several
times, observe the installa ion and assembly instructions of the manufacturer/
Check whether the right expanding head was used. Pipe expanded several
times, observe the installa ion and assembly instructions of the manufacturer/
Change expanding head.
Check whether the right expanding head was used. Pipe expanded several
times, observe the installa ion and assembly instructions of the manufacturer/
Change pressing head.
Charge the battery with the Li-Ion/Ni-Cd rapid charger, change the battery.
Have it checked/repaired by an authorised REMS customer service workshop.
Let the drive unit cool down for about 10 minutes.
REMS customer service workshop.
Charge the battery with the Li-Ion/Ni-Cd rapid charger or change the battery.
Have it checked/repaired by an authorised REMS customer service workshop.
Change expanding head.
Do not use the expanding head anymore! Clean the expanding head and
grease lightly with machine oil or change.
Reset the expander, see 2.5.
warranty only applies for new products which are purchased in the European
Union, in Norway or in Switzerland.
This warranty is subject to German law with the exclusion of the United Nations
Convention on Contracts for the International Sales of Goods (CISG).
to 36 months for the drive units listed in these operational instructions which
is that the drive unit shall be sent in for a payable inspection by an authorised
REMS customer service station at least every 12 months after delivery to the
the drive unit is dismantled, for example, and wearable parts inspected and
usually changed. The repeated inspec ion of electrical equipment also takes
place according to EN 62638:2010-08 (VDE 0702). After inspection, he author-
test badge. The date of delivery shall be documented by the submission of the
original purchase documents, compliance with the inspection intervals shall be
made before carrying out any necessary repairs.

9. Spare parts lists

For spare parts lists, see www.rems.de
g