Accessories; Multifunction Table - Festool TS 75 EQ Manual De Instrucciones Original

English
terrupted automatically and the machine comes
to a standstill.
In this case, take the unit to an authorised Cus­
tomer Service Centre and have the carbon
brushes changed.
Observe the following instructions:
► To ensure constant air circulation, always
keep the cooling air openings in the housing
clean and free of blockages.
► Use an extractor on all openings of the pow­
er tool to remove wood chips and splinters.
► Damaged safety devices and components
must be repaired or replaced in a recog­
nised specialist workshop, unless otherwise
indicated in the operating manual.
► When working with plaster- and cement-
bonded fibreboards, clean the tool particu­
larly thoroughly. Clean the vents of the
power tool and on/off switch using dry, oil-
free compressed air. Otherwise, gypsum
dust deposits may build up inside the power
tool's housing and on the on/off switch and
harden when exposed to humidity. This may
impair the switching mechanism.
► Check all warnings on the electric power
tool for readability and completeness. Re­
place missing or illegible warnings.
The plunging mechanism must always
move free and move back automatically
into starting position. Always keep the area
around the guard/ protective cover clean. Clear
from dust and chippings by blowing out with
compressed air or using a brush.
After being removed away from the workpiece,
the machine automatically returns to its basic
position, the saw blade retracts into the protec­
tive cover and the cut-in and release block en­
gages once again. If this no longer functions,
stop using the circular saw and have it repaired
immediately by an authorised Customer Service
Centre.
The riving knife must be aligned with the saw
blade, and should not be crooked. A faulty riving
knife must be replaced immediately. Under no
circumstances use the saw without the riving
knife because of the increased risk of recoil.
Even with proper usage the teeth of the saw
blade become blunt in time. Change the saw
blade as soon as you notice that you need a
greater force to push the machine during saw­
ing or the quality of cut has deteriorated. Take
blunt saw blades back to an authorised Cus­
tomer Service Centre for re-sharpening. Take
14
All manuals and user guides at all-guides.com
the saw blades out when you want to clean
them of resin and wood. Use kerosene for
cleaning the saw blades.

11 Accessories

Use only original Festool accessories and
Festool consumable material intended for this
machine. These components are designed spe­
cifically for this machine. Using accessories
and consumable material from other suppliers
will most likely affect the quality of your results
and limit warranty claims. Machine wear or
your own personal workload may increase de­
pending on the application. Protect yourself and
your machine, and preserve your warranty
claims by always using original Festool acces­
sories and Festool consumable material!
The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet under "www.festoolusa.com".
11.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli­
cations that are specially designed for your
Festool circular saw.
11.2 Parallel stop, table widener
A parallel stop can be used for section widths
up to 7-1/16" (180 mm). The parallel stop can
also be used as a table widener.
11.3 Side-mounted cover, false joints
The cover that can be mounted on the side of
the protective cover improves the effect of dust
extraction for 0° cuts.
Simultaneously, the cover can be used as a
false joint stop for false joint widths from 3/4"
(18 mm) onwards.

11.4 Multifunction table

The mutifunction table MFT/3 makes clamping
the workpiece easy and allows you to saw large
and small workpieces safely and precisely us­
ing the guide system. Its many fields of applica­
tion make economical and ergonomically con­
venient work possible.