Use; Improper Use; Warranty; Maintenance Reserved To The End User - Cattini Oleopneumatica YAK 214/P Manual Uso Y Mantenimiento

USE

USE
IMPOR IMPORT T ANT ANT: The jack must be used and operated in the horizontal position only in order not to compromise its operation. : The jack must be used and operated in the horizontal position only in order not to compromise its operation.
- Expressly observe the safety rules already described in this manual.
1) Position the jack under the supports as described in the manual of the vehicle the manufacturing company is not
responsible for any break or damage to the lifted vehicle or to persons or property due to an incorrect use of the
jack.
2. By pressing key A on the control block the lifting function is activated. DWG. 12
3. By pressing key B on the control block the lowering function is activated. DWG. 12
4. After lifting the load, it is absolutely essential to rest it on the support stands before doing any work under it.
REMEMBER THA REMEMBER THAT THE JACK IS A LIFTING DEVICE AND NOT A SUPPOR T THE JACK IS A LIFTING DEVICE AND NOT A SUPPORTING DEVICE!!
- The operator`s employer shall provide the necessary training and supply all information required to allow the
operator to use the jack safely.
- Before working with the jack, it is advisable to perform a few operations with no load in order to acquire the sensitivity Before working with the jack, it is advisable to perform a few operations with no load in order to acquire the sensitivity
necessary to work safely with the jack. necessary to work safely with the jack.
- When the jack is not used, always keep the pistons lowered

IMPROPER USE

IMPROPER USE
The air-hydraulic jack has been designed and made to lift transport vehicles. Any other use of the jack, such as for
instance lifting and/or moving persons, is considered to be definitely improper. All use of the jack not in conformity with the
safety rules listed in this manual is considered to be improper use.
W W ARRANTY ARRANTY
This jack is covered by a 12-month warranty starting from the date the jack leaves our factory unless the warranty has
been activated on-line; this covers all manufacturing defects but not transport expenses, defects caused by improper use
or damage suffered during transport. For more details please see the warranty card attached to this manual.
MAINTENANCE RESER MAINTENANCE RESERVED T
- For a long service life of the jack, it is advised to clean the pistons on the outside every fortnight.
- At least twice a year, check the level of oil in the tank.

CHECKING THE OIL LEVEL

CHECKING THE OIL LEVEL
IMPOR IMPORT T ANT ANT: The maximum amount of oil contained in this jack is 0.65 L. Compatible oil: A : The maximum amount of oil contained in this jack is 0.65 L. Compatible oil: ATF DEXRON IID
To check the oil level, follow the steps below:
1. Bleed the air out of the jack (see next section)
2. Position the jack, with the pistons lowered, in a horizontal position
3. Unscrew the screw
4. If once you unscrew the screw
oil. The level must be at the height of the screw
5. If the oil leaks, allow the excess quantity to flow until the correct level is reached (see p.4).
6. Tighten the screws
14
VED TO THE END USER O THE END USER
POS. 7 A06438 POS. 7 A06438 and then the screw
POS. 8 A06438 POS. 8 A06438
7, 8 - A06438. 7, 8 - A06438.
DWG. 12
DWG. 12
POS. 8 A06438 POS. 8 A06438 (DWG. 13 (DWG. 13)
there is no oil leakage, the level is too low. In this case top up the
POS. 8 A06438. POS. 8 A06438. (DWG. 13 DWG. 13)
TING DEVICE!!
TF DEXRON IID
EN EN