Manual Ignition; Switching Off; Setting The Time - Italiana Camini LITTLE Instalación Uso Y Mantenimiento

Manual ignition

At temperatures below 3°C (too low for the heating element to glow) or if the heating element is temporarily out of order, a fire-
lighter may be used for ignition. Put a piece of well lit firelighter in the combustion chamber, close the door and press ON/OFF.
Operating modes
(when the stove is working, press the A/m key to switch between modes).
Manual: set the working power (from P1 to P3) using the left knob and ventilation using the right knob.Automatic: set the desired
room temperature, the stove then sets the working power needed to reach it (P3) or maintain it (P1).When the temperature is set
below the current room temperature, the stove runs at P1, consuming a corresponding quantity of pellets.
Notes on flame variability
Changes in the flame depend on the type of pellets used, flame variability commonly associated with solid fuel and periodic
cleaning of the combustion chamber carried out automatically by the stove (which does NOT replace cold vacuuming by the user
before ignition).

Switching off

Hold the ON/OFF key down for 2 seconds to start the shutdown procedure; the message "of" is then displayed (for a total of 10
minutes).
During shutdown:
• Pellet loading ceases.
• Ventilation is turned up to maximum.
• The smoke expulsion motor is turned up to maximum.
Never unplug the stove whilst it is shutting down after an arrest.
WEEKLY TIMER PROGRAM BUILT INTO PANEL
The concept of the weekly timer program built into the central panel.
Three ignition programs can be set:
Pr01 with on and off time settings
Pr02 with on and off time settings
Pr03 with on and off time settings
One or more of the three programs can be enabled for each day of the week (day1=Monday;day2=Tuesday...day7=Sunday).
When on standby the display alternates between displaying the ignition mode (P1, P2 or P3 or a temperature) and the current time.
Refer to Page 20 for each of the buttons to be pressed.

Setting the time

Press the "Menu" key for 2 seconds until "tS" appears.
Press (-) and "Prog" will appear. Press "Menu" and "PrOF" will appear. Press the (-) key and "Set" will be displayed. Confirm
with the "Menu" key, which will display HOUR:MIN, values can then be varied with the (-) and (+) keys.
Once the hour has been set, confirm with "Menu" and the day number will appear (day 1=Monday, day2=Tuesday...
day7=Sunday) which can be varied with the (-) and (+) keys. Confirm with "Menu" and "Prog" will appear. Press "ON/OFF" to
exit from setting.
Enabling programs
Press "Menu" for 2 seconds and "tS" will appear. Press (-) and "Prog" will appear. Press "Menu" and "ProF" will appear.
Confirm by pressing the "Menu" key, pass now to "on" with the (-) or (+) keys. Confirm with the "Menu" key and "Prog" will
appear. Press "ON/OFF" to exit from setting. The stove in Pr On mode will receive timed on and off commands.
Setting a program (e.g. Pr01)
Press "Menu" for 2 seconds and "tS" will appear. Press (-) and "Prog" will appear. Press "Menu" and "ProF" will appear. Press
(+) until "Pr01" appears (after Pr On has been set previously).
Confirm with the "Menu" key and ON P1 will appear and then the desired set hour for programme 1 ignition.
The time can be changed using the On/off (-) or Am (+) keys.
Press the "hourglass" to confirm.
Of P1 appears followed by program 1 off time.
The time can be changed using the On/off (-) or Am (+) keys.Press the "hourglass" to confirm.ofd1 appears (indicating that
program 1 is not enabled for day1, Monday). Press Am (+) to enable it, after which Ond1 appears, indicating that program 1 is
enabled for Monday.
Press the "hourglass" to move on to the second day, Tuesday, and so on until day7.Press the "hourglass" to exit.
Pr 02 and Pr 03 on and off times and the days on which they are enabled can be set in a similar way.
A green light beside the "hourglass" symbol indicates that a program is enabled for that day.
- 21
-