BATHMATE HYDROXTREME Guia Del Usuario página 6

Using your Hydropump in the Shower
You may use the shower strap by sliding the connector onto the Hydropump leaving your hands free to wash.
1. Relax in the Shower for a few minutes.
2. Lock the valve by rotating the valve cap clockwise.
3. Push the black pip into the closed position with your finger, remove the comfort insert (to prevent trapped air) then invert the Hydropump under
the shower head until full of water.
4. Replace the comfort insert.
5. Place the Hydropump over your flaccid penis tight up to your pelvic seat with the black pip in the closed position. The chamfer can be
positioned facing either upwards or downwards depending on your level of comfort.
6. Make a seal against your body, ensuring that the positioning is comfortable and that your testicles are well clear.
7. With the Hydropump angled slightly upwards, open the valve by pushing the black pip to the central position and commence pumping.
8. Ensure that the black pip is in the central (open) position when pumping.
9. Pump slowly and evenly until the bellows remain depressed, indicating that optimal vacuum has been achieved.
10. To increase the vacuum further and for more control, use the hand ball pump either with the hose or connected direct to the pump. Please note,
the fit between the handball pump and the Hydropump valve is designed to be a non permanent connection. For this reason the handball
should be held in position whilst in use, and removed when optimum vacuum is achieved. If a more permanent connection is desired, please
use the hose connector.
11. Ensure you follow the recommended instructions.
12. To remove the Hydropump, unlock the valve by rotating the valve cap anti-clockwise and release the vacuum by depressing the valve cap
inwards to activate the quick-release mechanism and slide the Hydropump off your penis.
Using your Hydropump in the bath
1. Relax in the bathtub for a few minutes.
2. Remove the comfort insert (to prevent trapped air) and fill the Hydropump with bathwater.
3. Replace the comfort insert.
4. Place the Hydropump over your flaccid penis tight up to your pelvic seat with the black pip in the central (open) position. The chamfer can be
positioned facing either upwards or downwards depending on your level of comfort.
5. Make a seal against your body, ensuring that the positioning is comfortable and that your testicles are well clear.
6. With the Hydropump angled slightly upwards, ensure that the black pip is in the central (open) position and commence pumping.
7. Ensure that the black pip is in the central (open) position when pumping.
8. Pump slowly and evenly until the bellows remain depressed, indicating that optimal vacuum has been achieved.
9. To increase the vacuum further and for more control, use the hand ball pump either with the hose or connected direct to the pump. Please note,
the fit between the handball pump and the Hydropump valve is designed to be a non permanent connection. For this reason the handball
should be held in position whilst in use, and removed when optimum vacuum is achieved. If a more permanent connection is desired, please
use the hose connector.
10. Ensure you follow the recommended instructions.
11. To remove the Hydropump, unlock the valve by rotating the valve cap anti-clockwise and release the vacuum by depressing the valve cap
inwards to activate the quick-release mechanism and slide the Hydropump off your penis.
Cleaning and Maintenance
Wash out your Hydropump with warm soapy water and rinse thoroughly. Allow your Hydropump to dry and store in a dry place away from direct
sunlight.
Customer Care & Warranty
The Bathmate Hydropump is designed to provide many years of trouble free use. It is covered by a two year warranty against defective parts or
poor workmanship. Customer care and full details of the warranty can be seen at: www.bathmatedirect.com/support
In the unlikely event of a warranty claim, DX Products Ltd reserves the right to request the return of the Hydropump or provision of evidence of
damage.
Product Identification Code (PID)
DX Products Ltd uses an identification code for all products. Bathmate Hydropumps carry a unique 6 letter PID code, which you will find on the
label of your hydropump. This code is your assurance of authenticity and proof that you are buying a genuine product not an inferior counterfeit
copy. Please use your PID to authenticate your product and register your warranty online at our website: www.bathmatedirect.com/support
ENGLISH