Initial Setup; Before You Begin - Magnavox 22MF330B Manual Del Usuario

These operations are accessible by remote control.
Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit's initial setting
which includes selecting a language for your on-screen menu
and autoprogram, which automatically scans and memorizes
viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.
1
After making all the necessary connections,
press to turn on the unit.
• It may take a few moments to turn on the unit for the
first time.
• [Initial Setup] menu appears automatically after the
unit is turned on.
2
Use ▲/▼ to select the on-screen language from the
choices (English / Español / Français) on the right side of the
TV screen.
3
Use ▲/▼ to select [Antenna] for TV channels or [Cable]
for CATV channels, then press OK.
Initial Setup
Make sure the antenna is connected to ''ANT. IN'' jack.
Select your signal source.
Antenna
Or
Cable
Select OK
OK
[Autoprogram] will begin.
Initial Setup
Please wait while the system is scanning for channels. Auto programming
may take more than 20 minutes to complete.
0%
Digital channels
Analog channels
A0170̲N0UH̲EN̲v1.indd 15 A0170̲N0UH̲EN̲v1.indd 15
All manuals and user guides at all-guides.com
Antenna
Cable
Skip
ANT.IN
BACK MENU
Back Skip
0 ch
0 ch
MENU
Skip
4
Use ◄/► to select the desired location setting, then
press OK.
Initial Setup
Select "Retail" or "Home" for your location.
Retail
Select
Select [Retail] store, the unit will be set up with
predefined setting for retail displays. In this setting, the
power consumption may possibly exceed the limited
requirement of the ENERGY STAR
• Select [Home], the unit is set to maximize the energy
efficiency for home setting and it can be adjusted
through a choice of picture and sound quality according
to your preference.
• When the initial setup is completed, the lowest
memorized channel with the confirmation message of
the location setting will be displayed on the TV screen.
Note
•
If you are not receiving a signal from your cable service, contact the Cable
provider.
•
or MENU during autoprogram, this setting will be canceled.
If you press
•
The initial autoprogram function can be executed for either [Antenna] or
[Cable] only once. When you change the connection (Antenna / Cable),
➠
set [Autoprogram] again. p. 19
•
If there is no signal input from the antenna terminal and no operation for
several seconds after you turn on the unit, [Helpful Hints] appears. Follow
the instructions listed on the TV screen.
Initial Setup
No channel is registered.
Try Autoprogram again?
Verify that you have a cable connected to the "ANT. IN" jack on the back
of the TV, the channel installation process searches this connection. If
you are using a cable or satellite box, please confirm the input which
you have connected the box and press "SOURCE" key on the remote
control to select the appropriate source input.
Select
OK
•
You must set [Home] in step 4. Otherwise, the settings of picture and
sound quality you adjusted will not be memorized after you turn off the
unit.
After an initial setup is completed...
• If you want to scan the channels automatically again.
[Autoprogram] ➠ p. 19
• You can add the desired cable and analog channels
unmemorized by autoprogram.
[Add Channels] ➠ p. 20
• If you want to change to another language.
[Language Selection] ➠ p. 21
• If you want to change the location setting.
[Location] ➠ p. 31
English
Home
OK
OK
R R qualification.
®
Retry
Later
MENU
OK Skip
15
EN
2010/02/05 22:58:35 2010/02/05 22:58:35