Publicidad
Idiomas disponibles
Idiomas disponibles
■ Keep a firm grip with both hands while in operation.
The product should be held at a comfortable position
with the trigger hand or rear handle about hip height.
■ To help reduce the risk of kickback: Do not push into
the material to be cut. Move from right to left in steady
sweeps, moving forward a little at the beginning of
each new sweep.
■ Maintain your grip and balance on both feet. Position
yourself so that you will not be drawn off balance by
the kick-back reaction of the cutting blade.
■ Adjust the strap hanger to a comfortable position.
Exercise extreme caution when using the blade with
the product. Blade thrust is the reaction that may occur
when the spinning blade contacts anything it cannot
cut. This contact may cause the blade to stop for
an instant, and suddenly "thrust" the unit away from
the object that was hit. This reaction can be violent
enough to cause the operator to lose control of the
unit. Blade thrust may occur without warning if the
blade snags, stalls or binds. This is more likely to
occur in areas where it is difficult to see the material
being cut. For cutting ease and safety, approach the
weeds being cut from the right to the left. In the event
an unexpected object or woody stock is encountered,
this could minimize the blade thrust reaction.
TM
TRI-ARC
BLADE
TM
The Tri-Arc
blade is suited only for thicker weeds and
pulpy stalks. When the blade becomes dull, it can be
turned over to extend the life of the blade.
TM
Do not sharpen the Tri-Arc
CUTTING TECHNIQUE - BLADE
WARNING
The blades are very sharp and can injure even if they
are not moving. Exercise extreme caution when using
the blade with the product. Safe operation of this tool
requires that you read and understand this operator's
manual and all labels affi xed to the tool.
■ Both hands must be used at all times to control this
product. Keep a firm grip with both hands while in
operation.
■ Maintain your grip and balance on both feet. Position
yourself so that you will not be drawn off balance by
the kick-back reaction of the cutting blade.
■ Inspect and clear the area of any hidden objects such
as glass, stones, concrete, fencing, wire, wood, metal,
etc.
■ Never use blades near footpaths, fencing, posts,
buildings or other immovable objects.
■ Never use a blade after hitting a hard object without
All manuals and user guides at all-guides.com
English (Original instructions)
blade.
first inspecting it for damage. Do not use if any
damage is detected.
■ For cutting ease and safety, approach the weeds
being cut from the right to the left.
MAINTENANCE
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, poor performance, and may void
your warranty.
■ Always stop the engine and allow it cool before making
any maintenance.
■ You may make adjustments and repairs described
here. For other repairs, contact the authorised service
agent.
■ Consequences
of
include excess carbon deposits resulting in loss of
performance and discharge of black lubricant residue
dripping from the silencer.
■ For replacement line, use only nylon filament line of
the diameter described in the specification table of this
manual.
■ After extending the new cutter line, always return the
product to its normal operation position before starting.
■ The cutting attachment must not work in idle mode. If
this requirement is not satisfied, the clutch has to be
adjusted or the product needs an urgent maintenance
by a qualified technician.
■ After each use, clean the product with a soft dry cloth.
■ Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
REPLACING REELEASY
See fi gure 15a.
■ Open the
ReelEasy
TM
latches on each side. The contents of the string head
are spring loaded, so keep your other hand over the
string head cover while depressing the latches.
■ Remove the string head cover, bump knob, spool, and
spring then set aside.
■ Place the string head housing on the drive shaft. Make
sure the string head housing is fully seated.
■ Place the holding pin through the hole in the upper
flange washer and the hole in the gear head.
■ Place the hex bolt into the drive connector. Using the
25
WARNING
improper
maintenance
TM
STRING HEAD
string head by depressing the
may
Publicidad
