Publicidad
Idiomas disponibles
Idiomas disponibles
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Replacing filter of dust case
Optional accessory
1.
Remove the dust case while pressing down the
latch lever of the dust case.
► Fig.56: 1. Latch lever
2.
Lift the lock tab slightly outwards and open the
dust case cover.
► Fig.57: 1. Dust case cover 2. Lock tab
3.
Insert a flat-blade screwdriver in between the filter
case and dust case cover as shown in the figure. Press
the side walls of the filter case inwards, and lift the filter
case up off using the flat-blade screwdriver.
► Fig.58: 1. Flat-blade screwdriver 2. Filter case
3. Dust case cover
4.
Push the filter out of the filter case as shown in the
figure.
► Fig.59: 1. Filter 2. Filter case
5.
Replace a new filter in the filter case. Set the filter
case back onto the dust case aligning the guide projec-
tion on the filter case with the groove in the dust case.
► Fig.60: 1. Guide projection 2. Groove
6.
Close the dust case cover, and then reassemble
the dust case to the dust collection system.
Replacing sealing cap
Optional accessory
Replace a sealing cap at regular intervals as a worn
or damaged sealing cap may affect the suction
performance.
1.
Insert a flat-blade screwdriver, with its flat surfaces
vertical, into one of the release holes placed on the
sides of the nozzle head. Tilt the flat-blade screwdriver
at an angle to squeeze and pop the cube hook of the
sealing cap out of the molded receptacle. Then peel the
rubber edges of the sealing cap away from the rims of
the nozzle head opening.
► Fig.61: 1. Sealing cap 2. Cube hook 3. Release
hole 4. Nozzle head
2.
Set one of cube hooks of a renewed sealing cap
into the molded receptacle in the nozzle head with a
recessed surface of the sealing cap facing forwards.
► Fig.62: 1. Cube hooks 2. Receptacles 3. Sealing
cap 4. Recessed surface
3.
Place the other hook into the receptacle on the
opposite side of the nozzle head, while repositioning the
sealing cap to fit finely to the nozzle head.
► Fig.63: 1. Sealing cap 2. Cube hook 3. Receptacle
4. Nozzle head 5. Rims
4.
Gently lay the rubber edges of the sealing cap
down over the rims of the nozzle head opening from
bottom to top.
► Fig.64: 1. Rubber edges 2. Sealing cap 3. Nozzle
head
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
•
Carbide-tipped drill bits (SDS-Plus carbide-tipped
bits)
•
Core bit
•
Bull point
•
Diamond core bit
•
Cold chisel
•
Scaling chisel
•
Grooving chisel
•
Drill chuck set (chuck adapter / drill chuck)
•
Bit grease
•
Depth gauge
•
Blow-out bulb
•
Dust cup
•
Dust cup set
•
Hook set
•
Dust case set
•
Filter set
•
Joint
•
Dust collection system
•
Wireless unit
•
Safety goggles
•
Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
24 ENGLISH
Publicidad
