Publicidad
Idiomas disponibles
Idiomas disponibles
protected (Gr. 1-2-3).
•
That the child car seat restraint harnesses are always
at the right height, that is the shoulder straps (Gr. 1).
•
That the diagonal car safety belts are always at the
right height as the straps are slotted through the he-
adrest C (Gr. 2-3).
To adjust the height of the headrest, turn the knob A fi t-
ted at the top of the backrest until you reach the required
height (diag. 16).
REFITTING THE HARNESS FOR SEATING A GR. 1
CHILD (9-18 KG)
To refi t the restraint harness to the child car seat, proceed
as follows:
1.
Join the two ends of the harness straps, insert them
and connect them to the buckle (diag. 36)
2.
Insert the two locking plates R, sliding them out
through the slots in the fabric cover and pulling them
out from under the seat (diag. 37).
3.
Insert the two shoulder strap and the belt sequence N
locking plates through the two red diagonal belt slots
C and then through the backrest (diag. 38).
4.
Connect the two harness straps to the locking plate
Q (diag. 39).
CLEANING AND MAINTENANCE
•
HOW TO CLEAN THE FABRIC COVER
The child car seat's fabric cover can be removed and clea-
ned by hand or in a washing machine at 30°C. Please re-
fer to the cleaning instructions on seat fabric label which
illustrates the following washing symbols:
Machine
Hand
Do not
washable at 30°
washable
bleach
Never use abrasive detergents or solvents. Do not spin
dry the fabric cover, let it dry without wringing.
To remove the various sections of the fabric cover from
the child car seat frame, follow the instructions below:
1.
Release the child car seat harnesses from the buckle
(diag. 14)
2.
Rotate and release the two belt locking plates R found
under the seat (diag. 20A) sliding them out of the two
slots in the fabric cover (diag. 20B).
3.
Pull the cover up over the headrest and remove (diag.
40).
4.
To remove the backrest cover, open the velcro faste-
ners and slide out the two harness straps (diag. 41).
5.
Remove the child car seat backrest following the in-
structions in the paragraph "FITTING THE CHILD CAR
SEAT INTO THE CAR AND SEATING A GR. 3 CHILD
(22-36 KG) WITHOUT THE BACKREST" (points 1-3).
6.
Remove the seat cover by opening the velcro faste-
ners and the two zips (diag. 42).
To replace the parts of the fabric cover, follow the above
instructions in the reverse order.
HOW TO CLEAN THE PLASTIC OR METAL PARTS
All manuals and user guides at all-guides.com
Do not dry
Do not
Do not
clean
spin dry
iron
10
Clean the plastic and coated metal parts only with a
damp cloth. Never use abrasive detergents or solvents.
The movable parts of the child car seat must not be lu-
bricated.
CHECKING THE CONDITION OF THE COMPO-
NENTS
It is recommended to check regularly the condition of
the following components to ensure that they are not
damaged or worn out:
•
Lining: check that the padding does not come out
from the seams. Check the condition of the seams:
they must always be intact and undamaged.
•
Harnesses: Check that the fabric weft is not frayed or
the harness strap worn out in the parts corresponding
to the adjustment strap, crotch, shoulders and har-
ness adjustment plate.
•
Plastic parts: Check that the plastic parts are not worn
out, damaged or faded.
WARNING! If the child car seat is deformed or worn out,
it must be replaced: it may no longer comply with the
original safety standards.
STORING THE PRODUCT
When it is not fi tted into the car, it is recommended to
store the child car seat in a dry place, away from sources
of heat and to protect it from dust, humidity and direct
sunlight.
DISPOSING OF THE PRODUCT
When the child car seat no longer complies with the
original safety standards, stop its use and dispose of it at
an appropriate collection point. Dispose of the product
as laid down in the environmental regulations in force in
the Country of use.
FOR FURTHER INFORMATION:
ARTSANA SPA
Customer Care
Via Saldarini Catelli, 1
22070 Grandate COMO-ITALY
Free-phone 800.188.898
http://www.chicco.com
Publicidad
