ROBLIN ARROW Murale 900 Instrucciones De Instalación E Utilización página 12

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 27
GB
All manuals and user guides at all-guides.com
Motor
Press LED button 2 to switch 'ON' the fan motor (and adjust the speed of the fan motor by pressing the
LED button '+' and '-') and the LED lights 2, 3 and 4 will illuminate. The fan speed will be increased if
constant pressure is kept on the (+) button.
LED 2
: Minimum speed - cooking with one pan or simmering
LED 2 & 3
: Medium speed - normal cooking with up to 4 pans
LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours
Press LED button 5 to obtain the boost position for maximum effect and the LED will illuminate to confirm
fan is switched 'ON'.
C - COMPLEMENTARY INSTRUCTIONS
• Boost speed :
To obtain the best performance it is advisable to switch 'ON' the cooker hood a few minutes (in the boost
setting) before you start cooking. To program the complementary function, proceed as follows:
- Press LED button 2 to switch 'ON' the fan motor and adjust the speed of the fan by pressing the LED
button '+' and '-'. You should keep applying pressure to the '+' and '-' button until the required speed is
selected.
- Press LED button 5 (boost speed) to switch 'ON' the fan motor in the boost setting. Press LED button 5
to switch 'OFF' the boost setting immediately.
It is advisable too that you should leave it running in the boost setting for approximately 5 minutes after
finishing.
• Pre-set stop of the boost speed :
A pre-set stop after 5 minutes of the boost speed is available.
Your cooker hood is supplied with a deactivated pre-set stop of the boost speed. To use the cooker hood
with a pre-set stop of the boost speed re-programme the hood as follows:
The lights and the fan motor should be switched 'OFF' to set the timer.
Push the LED button '-' until the LED lights will flash :
One flash of the LED lights 2,3, and 4 = function is switched 'OFF'.
Two flashes of the LED lights 2,3, and 4 = function is switched 'ON'.
While the 5 minutes timer is running, It is available to stop immediately the boost speed by pressing the
led button 5.
While the 5 minutes timer is running, the indication of saturation of the filters is switched 'OFF'.
If a pre-set stop for the hood is switched 'ON' and the 5 minutes timer is still running, the boost speed will
be switched 'OFF' together with the pre-set stop for the hood after the count down of 5, 10 or 15 minutes.
It is available to stop the boost speed before the count down of the preset stop of the hood by pressing
the led button 5.
• Pre-set stop for the hood :
This function allows you to program the cooker hood to automatically stop cooking after a pre-set period.
The lights and the fan motor should be switched 'OFF' to set the timer.
Proceed by repeatedly pressing the LED button 5 (Boost speed):
Two flashes of the LED button 1 & 5 = 5 minutes delay.
Three flashes of the LED button 1 & 5 = 10 minutes delay.
Four flashes of the LED button 1 & 5 = 15 minutes delay.
One flash of the LED button indicates the function is switched 'OFF'.
You can switch the cooker hood 'ON' and adjust the speed. The LED buttons 2, 3 and 4 will flash to
indicate the fan motor is switched 'ON' and which speed has been selected.
One flash = stop after 15 minutes.
Two flashes = stop after 10 minutes.
Three flashes = stop after 15 minutes.
• Indication of saturation of the metal grease filters :
After 200 hours use, one quick flash of the LED 1 will indicate that you must clean the metal grease
10

Publicidad

Tabla de contenido
loading

Tabla de contenido