Technical Data; On/Off Switch - Rupes LH19E Manual De Instrucciones

TECHNICAL DATA

MODEL
TYPE
Ø POLISHING FOAM mm
INSULATION CLASS
Ø BACKING PAD mm
POWER
Ø ORBIT mm
n NOMINAL RPM
POWER
ELECTRONIC SPEED CONTROL
BUFFER PAD AND BUFFER DIAMETER MAX R.P .M.
WEIGHT
SPINDLE THREAD
ELECTRONIC SPEED CONTROL
WEIGHT
INSULATION CLASS
VOLTAGE
VOLTAGE
ABSORBED CURRENT
ABSORBED CURRENT
LH19E
LK900E
10
7
6
8
4
4
7
INTENDED USE
INTENDED USE
The LH19E heavy-duty polishers is designed for polishing painted
or unfinished metal, fiberglass, and composite surfaces in
professional applications. Common examples of use include but
are not limited to: auto/marine/RV/motorcycle detailing and finish
correction, boat construction and repair, and metal finishing.
Do not use in the presence of flammable liquids or gases.
Do not let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
MOTOR
MOTOR
Be sure your power supply agrees with the voltage marked on
Be sure your power supply agrees with the voltage marked on
the nameplate. 120 Volts AC 60Hz means alternating current
the nameplate. 120 Volts AC 60Hz means alternating current
only. Voltage decrease of more than 10% will cause loss of
only. Voltage decrease of more than 10% will cause loss of
power and overheating.
power and overheating.
PARTS OF THE TOOL
PARTS OF THE TOOL
1 - Identification plate

2 - ON/OFF switch

3 - Electronic speed control
4 - Spindle shaft
5 - Handle site
6 - Cap
7 - Plate pad
8 - Srews
9 - Switch locking botton
10 - Botton lock
11 - Ventilator motor
12 - Handle
13 - Scews for handle
ON/OFF SWITCH
14 - Locking screws
WARNING: To reduce the risk of injury, make sure the
ON/OFF SWITCH
polisher is not resting on the workpiece when the switch
WARNING: To reduce the risk of injury, make sure the
is turned on.
polisher is not resting on the workpiece when the switch
is turned on.
To turn the polisher on, push the lever of the switch (2) towards
the body of the tool; if the polisher is to be locked in ON position,
To turn the polisher on, push the lever of the switch (2) towards
press button ( ) at the same time and keep it pressed while 9
the body of the tool; if the polisher is to be locked in ON position,
releasing lever, thus locking the switch.
6
/min
3
11
3
ON
OFF
8
6
1
5 1
5
14
W
Kg
7
2
2
9
8
13 (
optional)
To turn the polisher off, release the lever or, if locked in ON
press button (9) at the same time and keep it pressed while rele-
position, push the lever to release the lock button.
asing lever, thus locking the switch.
To turn the polisher off, release the lever or, if locked in ON
ELECTRONIC SPEED CONTROL
position, push the lever to release the lock button.
The polisher electronic speed control supply the following fea-
ELECTRONIC SPEED CONTROL
tures.
The polisher electronic speed control supply the following fe-
Speed Adjustment
atures.
Speed Adjustment
The speed can be adjusted in two ways: by means of the variable
actuation switch (2), by means of the adjustment wheel fitted on
the upper part of the machine (3).
Adjustment by means of the wheel (3) affects the adjustment
made using the variable actuation switch (2), determining the ma- Speed compensation
ximum speed of the motor.
In case of overloading the polisher, the electronic speed control
The speed must be selected according to the characteristics of the
will compensate and maintain the selected speed till a safe level.
pads and those of the material to be machined.
Exceeding this overload level may result in strong vibrations and
Speed compensation
tool overtemperature.
In case of overloading the polisher, the electronic speed control
Starting acceleration ramp
will compensate and maintain the selected speed till a safe level.
To avoid kickback effect and compound splattering, the
Exceeding this overload level may result in strong vibrations
electronic speed control always supply a smooth starting
and tool overtemperature.
acceleration ramp when the tool is turned on.
Starting acceleration ramp
Accidental re-start protection
To avoid kickback effect and compound splattering, the electro-
In case of a sudden lack of main power supply, the electronic
nic speed control always supply a smooth starting acceleration
ramp when the tool is turned on.
speed control prevents the re-start after the power supply
Accidental re-start protection
restoring if the main switch is turned on. The polisher must be
In case of a sudden lack of main power supply, the electro-
turned off and on again pushing the lever of the switch (2)
nic speed control prevents the re-start after the power supply
toward the body of the tool.
restoring if the main switch is turned on. The polisher must
be turned off and on again pushing the lever of the switch (2)
OPERATION
toward the body of the tool.
WARNING: To reduce the risk of injury, turn unit off and
OPERATION
disconnect it from power source before installing and
removing accessories, before adjusting or when making
WARNING: To reduce the risk of injury, turn unit off
repairs. Be sure the switch is in the "OFF" position. An
and disconnect it from power source before installing
accidental start-up can cause injury
and removing accessories, before adjusting or when
making repairs. Be sure the switch is in the "OFF" posi-
WARNING: Never modify any parts of the power tool.
tion. An accidental start-up can cause injury
Damage or personal injury could result.
LH19E
/ II
1200
450 ÷ 1700
YES
200
5/8''
2,25
120 V AC – 60Hz
8.5 A
12 (
optional)
1
5
9
4
ENGLISH
LK900E
165
150
5
900
250÷560
2,70
•
/ II
120 V AC - 60 Hz
7 A
3
10
ON
OFF
2
6
2
9