Martin Yale intimus 175SC2 Instrucciones De Uso página 6

Translation of the Original Operation Manual
GB
Übersetzung der Originalbetriebsanleitung
7 = Control display (Fig. 1)
"Oil cutters"
Comes on when the cutters in the cross
cut version must be oiled. The lubrication
procedure must be acknowledged on
the reverse button (4) (see description in
"CUTTER MAINTENANCE").
8 = Control display (Fig. 1)
"Door open"/ "Door malfunction"
a) "Door open"
Comes on if the door on the lower part
of the machine is opened. The machine
switches off automatically and cannot
be started as long as the door remains
open.
b) "Electrical fault"
Flashes when there is an electrical
fault in the door sensor. The machine
switches off. Please contact your
dealer.
9 = Control display (Fig. 1)
"Motor overload" /
"Electrical fault"
To find out what to do see the relevant
description under the "MALFUNCTION"
section.
a) "Motor protection"
Comes on when the motor has been
overloaded and has switched off. The
machine cannot be started while the
motor is cooling down.
b) "Electrical fault"
Flashes when there is an electrical fault
inside the control board. At the same
time the function button (1) LED display
flashes. The machine switches off.
Please contact your dealer.
10 = Control display
"Collection bin full" (Fig. 1)
Lit when the collection bin is full and needs
to be emptied.
The cutter is switched off.
11 = Guide rail (Fig. 3)
Ensures trouble free feed-in of EDP paper
as far as possible.
5
6
7
8
Fig. 1
OPERATION
SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to
"Ready":
- Press the function button (1) briefly.
- The function button (1) LED display
on for "Ready".
- The machine can be loaded.
FEEDING OF SINGLE SHEETS:
- Feed paper through the inlet guide to the cut-
ting system.
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
Note: For shredding transparent films, the
machine must be manually switched to forwards
running (press and hold the forwards button (2)
for approx. 2 secs.).
By briefly pressing the function button (1) (Stop
function), the shredding process can be stopped
at any time. To continue, press and hold the
forwards button (2) for approx. 2 secs.
If the machine is not used for a period of approx.
5 mins., it automatically switches off.
FEEDING OF COMPUTER PAPER:
- Insert the paper underneath the guide rail (11)
(fig. 3) and feed it through the inlet guide to the
cutting system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
Note: In order to always obtain a correct cutting
result in terms of particle size and thus achieve
the safety class according to DIN 32757 as
stated in the brochure, the material to be cut
must always be fed into the cutting mechanism
at a right angle to the cutting mechanism and in
appropriate quantities in the middle of the inlet
slot.
2
9
1
10
3
11
Fig. 3
comes
EMPTYING THE RECEPTACLE (fig. 4:
When the receptacle is full, the machine turns off
automatically. The control display
on. Empty the receptacle as follows:
- Open the door. The control display
- Remove the bag and dispose of the contents.
- PLace empty sack into receptacle and close
- If the control display
Note: The machine will only run if the door is
closed.
DYNAMIC LOAD DISPLAY:
To prevent a material jam and therefore ensure
continual and effective destruction of the data
storage media, the current load level of the
motor is displayed during the shredding process
by means of different colour lights on the control
display (5) (Fig. 1) next to the control buttons as
follows:
Green light:
Yellow light:
Red light:
6
Never feed the shredder with a
quantity of material exceeding the
maximum indicated.
TECHNICAL DATA section!
S h o u l d t h e m a c h i n e
overloaded, follow the instructions under
"MATERIAL JAM IN MACHINE" under
"MALFUNCTIONS".
on. If there is still material in the feed slot, the
control display (6) also comes on.
The control display (10) goes out.
door. The control display (8) goes out.
(6) comes on, press
the forward button (2) briefly. The remaining
material in the feed slot is shredded and the
display go out.
load < 50%
load 50 - 75%
load 75 - 100%
Fig. 4
Refer to the
b e c o m e
(10) comes
(8) comes