Publicidad
Idiomas disponibles
Idiomas disponibles
English
AC Input Rating Amperes*
Equal to or
greater than
0
2
3
*
If the input rating of a charger is given in watts rather
than in amperes, the corresponding ampere rating is
to be determined by dividing the wattage rating by the
voltage rating–for example:
1,250 watts
125 volts
8. Do not operate charger with damaged cord or plug-
replace them immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualifi ed serviceman.
10. Do not disassemble charger; take it to a qualifi ed
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric
shock or fi re.
11. To reduce risk of electric shock, unplug charger from
receptacle before attempting any maintenance or
cleaning. Removing the battery will not reduce this
risk.
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
CHARGER
You must charge the battery before you can use the power
tool. Before using the model UC18YSL3 battery charger,
be sure to read all instructions and cautionary statements
on it, the battery and in this manual.
CAUTION
USE ONLY metabo HPT BATTERY TYPE
BSL36B18. OTHER TYPES OF BATTERIES MAY
BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING
Improper use of the battery or battery charger
can lead to serious injury. To avoid these
injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged
or is completely worn out. The battery can explode in
a fi re.
6
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR CHARGER
but less
than
2
3
4
= 10 amperes
Table 1
AWG Size of Cord
Length of Cord, Feet (Meter)
25 (7.5)
50 (15)
18
18
18
18
18
18
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the charger air vents.
Electric shock or damage to the charger may result.
5. NEVER use outdoors. Keep the battery away from
direct sunlight and use only where there is low
humidity and good ventilation.
6. NEVER charge when the temperature is below 14°F
(-10°C) or above 104°F (40°C). (UC18YSL3)
NEVER use when the temperature is below 32°F
(0°C) or above 104°F (40°C). (BSL36B18)
7. NEVER connect two charger together.
8. NEVER insert foreign objects into the hole for the
battery or the charger.
9. NEVER use a booster transformer.
10. NEVER use DC power.
11. NEVER store the battery or charger in places where
the temperature may reach or exceed 104°F (40°C)
such as inside metal box or car.
12. NEVER expose the battery or charger to rain or wet
conditions.
13. ALWAYS operate charger on standard household
electrical power (120 volts). Using the charger on any
other voltage may overheat and damage the charger.
14. ALWAYS wait at least 15 minutes between charges to
avoid overheating the charger. (UC18YSL3)
15. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the
motor stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
100 (30)
150 (45)
18
16
16
14
16
14
Publicidad
