Maintenance Chart; Carburetor Adjustment; Emissions Control - Briggs & Stratton 120000 Power Built 825 Manual Del Operario

WARNING
Engines give off carbon monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide can cause nausea, fainting or death.
Start and run engine outdoors.
•
Do not start or run engine in enclosed area, even if doors or windows are open.
•
CAUTION: This engine was shipped from Briggs & Stratton without oil. Before you start
the engine, make sure you add oil according to the instructions in this manual. If you
start the engine without oil, it will be damaged beyond repair and will not be covered
under warranty.
1. Check the oil level. See the How To Check/Add Oil section.
2. Make sure equipment drive controls, if equipped, are disengaged. See the equipment
manual for location and operation of these controls.
3. Turn the fuel shut-off valve (A), if equipped, to the on position (Figure 6).
4. Move the choke control lever (B) to the choke
Note: Choke is usually unnecessary when restarting a warm engine.
5. Move the throttle control lever (C), if equipped, to the fast
the engine with the throttle control lever in the fast position.
6. On engines equipped with a stop switch (D), move the switch to the on position.
7. Rewind Start: Firmly hold the starter cord handle (E). Pull the starter cord handle
slowly until resistance is felt, then pull rapidly.
Note: If the engine does not start after three attempts, go to
BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
WARNING:
Rapid retraction of the starter cord (kickback) will pull your
hand and arm toward the engine faster than you can let go. Broken bones,
fractures, bruises or sprains could result. When starting engine, pull the starter cord
slowly until resistance is felt and then pull rapidly to avoid kickback.
8. Electric Start: Push in the safety key (F). Momentarily push the start switch (G).
When the engine starts, release the switch (Figure 7).
Note: If the engine does not start after three attempts, go to
BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
9. As the engine warms up, move the choke control (B) to the run
(Figure 6).
How To Stop The Engine - Figure 8
WARNING
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Do not choke the carburetor to stop engine.
•
1. On models equipped with a throttle control lever (A), move the throttle control lever to
slow and then to the stop
Move the stop switch (B), (if equipped) to the stop position.
Electric Start: Remove the safety key (C). Keep the safety key out of reach of
children.
2. After the engine stops, turn the fuel shut-off valve (D) to the closed position.
Maintenance
Use only original equipment replacement parts. Other parts may not perform as
well, may damage the unit, and may result in injury. In addition, use of other parts
may void your warranty.
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
CAUTION: All the components used to build this engine must remain in place for proper
operation.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems
may be performed by any non-road engine repair establishment or individual.
However, to obtain "no charge" emissions control service, the work must be performed
by a factory authorized dealer. See the Emissions Warranty.
8
position.
position. Operate
position (see Figure 8).
or
or
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation,
or laceration.
Fire hazard
Before performing adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
•
Use only correct tools.
•
Do not tamper with governor spring, links or other parts to increase engine speed.
•
Replacement parts must be the same and installed in the same position as the
•
original parts.
Do not strike the flywheel with a hammer or hard object because the flywheel may
•
later shatter during operation.
When testing for spark:
Use approved spark plug tester.
•
Do not check for spark with spark plug removed.
•

Maintenance Chart

First 5 Hours
Change oil
•
Every 8 Hours or Daily
Check engine oil level
•
Clean area around muffler and controls
•
Clean finger guard
•
Every 25 Hours or Annually
Clean air filter *
•
Clean pre-cleaner *
•
Every 50 Hours or Annually
Change engine oil
•
Check muffler and spark arrester
•
Every 100 Hours
Change gear reduction oil (if equipped)
•
position
Annually
Replace air filter
•
Replace pre-cleaner
•
Replace spark plug
•
Replace fuel filter
•
Clean air cooling system *
•
Check valve clearance **
•
* In dusty conditions or when airborne debris is present, clean more often.
** Not required unless engine performance problems are noted.

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor was set at the factory to
operate efficiently under most conditions. However, if adjustments are required, see any
Briggs & Stratton Authorized Dealer for service.
CAUTION: The manufacturer of the equipment on which this engine is installed specifies
the top speed at which the engine will be operated. Do not exceed this speed.
How To Replace The Spark Plug - Figure 9
Check the gap (A, Figure 9) with a wire gauge (B). If necessary, reset the gap. Install
and tighten the spark plug to the recommended torque. For gap setting or torque, see the
Specifications section.
Note: In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same
type for replacement.
Inspect Muffler And Spark Arrester - Figure 10
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.
•
Remove accumulated debris from muffler area and cylinder area.
•
Install and maintain in working order a spark arrester before using equipment on
•
forest-covered, grass-covered, brush-covered unimproved land. The state of
California requires this (Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on federal land.
BRIGGSandSTRATTON.COM