Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
29. POSITIONING OF TILE SAW (See HK I W TG "3)
A. To avoid the possibility of the appliance plug
or receptacle getting wet, position the tile saw
to one side of a wall-mounted receptacle to
prevent water from dripping onto the
receptacle or plug. The user should arrange a
"drip loop" in the cord connecting the saw to a
receptacle. The "drip loop" is that part of the
cord below the level of the receptacle, or
connector if an extension cord is used, to
prevent water traveling along the cord and
coming in contact with the receptacle.
B. If the plug or receptacle does get wet, F Q"P QV
unplug the cord. Disconnect the fuse or circuit
breaker that supplies power to the tool. Then,
unplug and examine for presence of water in
the receptacle.
30. EJ G EM "F K COQP F "DN CF G U "ECTG HW N N [ for cracks,
nicks, missing diamond matrix, or out-of alignment. Replace blades immmediately. F Q"P QV use damaged
blades. They may cause bodily injury.
ELECTRICAL REQUIREMENTS
•
VJ K U "VK N G "U CY "OW U V"DG "EQP P G EVG F "VQ"C"I TQW P F G F "RQY G T"U QW TEGwhile in use to protect the operator from
electrical shock.
•
K P "VJ G "G XG P V"QH"C"OCN HW P EVK QP "QT"DTG CM F QY P ."grounding provides a path of least resistance for electrical
current to reduce the risk of electrical shock. The tile saw is equipped with an electrical cord with a grounding
conductor and a grounding plug. Insert the 3-prong electrical plug into a 3-pole receptacle that is properly installed
and grounded in accordance with all local codes and ordinances.
•
F Q"P QV"OQF K H[ "VJ G "RN W I provided if it will not fit the outlet. Have the proper outlet installed by a qualified
electrician.
•
K ORTQRG T"EQP P G EVK QP "QH"VJ G "G S W K ROG P V/ I TQW P F K P I "EQP F W EVQT"ECP "TG U W N V"K P "C"TK U M "QH"G N G EVTK E
U J QEM 0The conductor with insulation that is green on the outside (with or without yellow stripes) is the
equipment-grounding conductor. If repair or replacement of the electrical cord or plug is necessary, do not connect
the equipment-grounding conductor to a live terminal.
•
EJ G EM "Y K VJ "C"S W CN K HK G F "G N G EVTK EK CP or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded.
•
W U G "QP N [ "5/ Y K TG "G ZVG P U K QP "EQTF Uthat have 3-prong grounding plugs and 3-pole receptacles that accept the
tile saw's plug.
•
TG RCK T"QT"TG RN CEG "F COCI G F "QT"Y QTP "EQTF "K OOG F K CVG N [ 0
•
K H"VJ G "RN W I "QT"TG EG RVCEN G "F QG U "I G V"Y G V."F Q"P QV"W P RN W I "VJ G "EQTF 0Disconnect the fuse or circuit breaker
that supplies power to the tool. Then, unplug and examine for presence of water in the receptacle.
•
QP N [ "W N / N K U VG F "G ZVG P U K QP "EQTF U "U J QW N F "DG "W U G F "Y K VJ
VJ K U "RTQF W EV0
•
K ORTQRG T"W U G "QH"G ZVG P U K QP "EQTF U "OC[ "ECW U G
K P G HHK EK G P V"QRG TCVK QP "QH"[ QW T"VQQN . which can result
in overheating. Be sure your extension cord is rated to
allow sufficient current flow to the motor. For the proper
gauge for this tile saw, please refer to VCDN G "3.
•
F Q"P QV"N G V"[ QW T"HK P I G TU "VQW EJ "VJ G "VG TOK P CN U
of plug when installing or removing the plug to or from
the outlet.
•
VJ K U "VK N G "U CY "OW U V"DG "RTQRG TN [ "I TQW P F G F 0
The risk of electric shock and bodily injury are greatly
increased if it is not, particularly when used in damp
locations or in proximity to plumbing.
WARNING:This product contains one or more chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
FIGURE 1
POWER SUPPLY
CORD
DRIP LOOP
FIGURE 2
(A) GROUNDING PIN
- 3 -
SUPPORTING
TILE SAW
SURFACE
METAL SCREW
(B) GROUNDED OUTLET BOX
(C) GROUNDING ADAPTER
(Not Permitted In Canada)
Publicidad
Tabla de contenido
