Switching The Light On And Off; Operation Via A Light Controller; Dmx Connection - IMG STAGELINE PARL-12DMX Manual De Instrucciones

Once the control signals from the master unit are
present at the slave units, they are controlled by the
master unit and the dot behind the first position on
the display (5) flashes. If a slave unit does not
receive any control signals, the indication
appears on its display.
5.3 Remote control via FS-2PARL
Via the foot-operated remote control FS-2PARL
available as an accessory, up to 50 spotlights can
be controlled together.
1) Connect the jack RJ45 (18) on the rear side of
the remote control FS-2PARL via the supplied
cable to the jack REMOTE (11).
2) Adjust the spotlight to the DMX address 001
( chapter 5.4.2).
3) No DMX signal must be present at the input
DMX INPUT (12).
4) Via the output DMX OUTPUT (13) further PARL-
12DMX units may be connected (
5.2) to control them together with the main unit
via the remote control. For the identical control
of the slave units in principle, adjust their DMX
address to 001 as well. For partly opposite con-
trol and running light effects for the music-con-
trolled programmes
5.3.2) set the slave units to the DMX addresses
005, 009, 013, 001, 005, 009, 013, etc.

5.3.1 Switching the light on and off

The light is switched off and on again with the but-
ton BLACKOUT (17) on the remote control. With
the light switched off (Blackout) the display (14) of
the remote control is dark.
It is possible to select another colour or another
light programme with the light switched off (
following chapters). Then the selection is shown on
the display (14) but will only be active when the but-
ton BLACKOUT is pressed again.
5.3.2 Programmes
The following programmes may be selected with
the button MODE (16):
The lighting colour changes automatically
with slow fadings.
The lighting colour is changed by music
control.
The lighting colour is changed by music
control, partly with running light effects for
several spotlights.
Music-controlled stroboscope in white
chapter
and ( chapter
the
Music-controlled stroboscope with chang-
ing colours, partly opposite for several
spotlights.
For music control the remote control has a micro-
phone (19) of its own. Adjust the control SENSI-
TIVITY (20) for the microphone sensitivity so that
the dynamic power of the music is reproduced by
the spotlight in an optimum way. For programmes
and , the colours are automatically
changed during music breaks after a few seconds.
The programme last selected is automatically saved.
5.3.3 Colour spotlight with selectable colour
The following colours can directly be selected with
the button COLOUR (15):
white
red
green
blue
purple
cyan
yellow
pink
orange
light green
The colour last selected is automatically saved.

5.4 Operation via a light controller

For operation via a light controller with DMX512
protocol (e. g. DMX-1440 or DMX-510USB by "img
Stage Line"), the PARL-12DMX is equipped with
four DMX control channels. The functions of the
channels and the DMX values can be found in
chapter 7.1.

5.4.1 DMX connection

For the DMX connection, the unit is provided with
3-pole XLR jacks of the following pin configuration:
Pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, special cables for high data flow
should be used. Standard microphone cables with
screening and a minimum cross section of 2 ×
0,22 mm 2 and with a capacity as low as possible
can only be recommended for a total cable length
of up to 100 m. For cable lengths exceeding 150 m
it is recommended to insert a DMX level matching
amplifier (e. g. SR-103DMX by "img Stage Line").
1) Connect the DMX input (12) to the DMX output
of the light controller.
GB
13