Getting The Appliance Ready For Use - Barbecook CAMPO INOX Manual De Instrucciones

Your pressure regulator and coupling may be different
from the ones in the illustrations.
6. Do one of the following:
• If you detect a leak, continue as described in "In case of
a gas leak".
• If there are no leaks, close the gas supply, rinse all
components thoroughly with water and dry them well.
5.6 In case of a gas leak
1. Close the gas supply and do one of the following:
• If you detected a leak on one of the connections, tighten
that connection.
• If you detected a leak on the cylinder or hose, replace
the cylinder or hose.
2. Recheck the connection or component on which you
detected the leak.
3. If the leak is not repaired, contact a Barbecook dealer. Do
not use the appliance until the leak is repaired.
For a list of nearby Barbecook dealers, refer to
www.barbecook.com.
6 GETTING THE APPLIANCE READY
FOR USE
6.1 Prior to first use / after prolonged
period of non use
Do not use the barbecue before you haveread, understood and
checked all informationin this manual. Ensure that:
• The barbecue is correctly installed
• There is no leak in the gas supply (see "5)
• The burners are correctly installed, the venturi tubes are
properly placed over the openings of the gas valves,
there are no obstructions (see safety information
cleaning of the burners)
• None of the gas supply hoses can come into contact with
a hot surface
• Your barbecue is installed in a safe place
6.2 Lighting the burners
You must have followed all the checks and procedures in the
section headed "Before the first use" before igniting the Plancha.
• Do not lean directly over the Plancha when lighting the
burners. The control knobs on the Plancha must be in the
OFF position.
• Open the tap on the gas cylinder slowly. Before turning the
control knob on one burner, wait for about 10 seconds to
allow the gas to stabilise.
• Never try to light all the burners at once.
6.3 Lighting the burners using the igniter
• Open the tap on the gas cylinder.
• Press one of the two knobs in and turn it to HIGH. You will
hear the piezo ignition light once when it clicks.
• The spark will light the burner.
• If the burner does not ignite after three attempts, turn off the
gas and wait for five minutes before trying again. This will
allow accumulated gas to disperse. Try again, repeating the
previous steps.
• If the burner still fails to ignite, read the "Troubleshooting"
section to determine the cause and the solution, or use a
match as explained below.
6.4 Lighting the burners using a match
Remove the griddle from the appliance. Now the burners are
visible and easy to reach. You can now light the burners using a
long match if the piezo ignition does not work.
• Open the tap on the gas cylinder.
• Hold the lighted match through the opening about 13 mm
from the burner.
• Press in the desired knob and turn to 'High'. The fire should
light within five seconds. If not, turn the knob off and wait
for five minutes to allow the gas to disperse.
• Repeat steps 1 to 5. If the burner still fails to ignite after
three attempts, read the "Troubleshooting" section.
6.5 Lighting the other burner
The second burner is lit in the same way as the first.
6.6 Visual check of the flames
Each time you light a burner, you have to check its flames. A
perfect flame is almost completely blue, with some yellow at the
top. Sporadic yellow flames are normal and not harmful.
If there is something wrong with the flames, do one of the
following to solve the problem:
If the flames are...
and
and
Low and entirely yellow
Higher than the bowl
www.barbecook.com
Do the following...
1. Immediately close the gas
supply and set all control
knobs to OFF.
2. Refer to "Troubleshooting"
to determine the cause of
the problem. Most likely, the
venturis are blocked.
1. Immediately close the gas
supply and set all control
knobs to OFF.
2. Wait 5 minutes to allow any
accumulated gas to escape.
3. Relight the burner(s).
4. If the problem persists, refer to
"Troubleshooting" to determine
the cause of the problem.
LOW HIGH
7