Makita LS1214 Manual De Instrucciones página 15

1
(2)
(1)
(4)
(2)
(3)
(1)
(2)
(1)
Measuring
Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length at the
back of the workpiece is the same as wall length.
Adjust cut length for angle of cut. Always use sev-
eral pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the
bevel angle and miter angle as indicated in the
table (A) and position the moldings on the top sur-
face of the saw base as indicated in the table (B).
In the case of left bevel cut
Table (A)
Molding
position in
52/38˚ type
Fig. A
(1)
For inside
corner
(2)
Left 33.9˚
(3)
For outside
corner
(4)
Table (B)
Molding
Molding edge against
position in
Fig. A
Ceiling contact edge should
(1)
be against guide fence.
For inside
corner
(2)
Wall contact edge should be
against guide fence.
(3)
For
outside
Ceiling contact edge should
corner
(4)
be against guide fence.
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
• Tilt and secure bevel angle setting to
33.9° LEFT.
• Adjust and secure miter angle setting to
31.6° RIGHT.
• Lay crown molding with its broad back
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
001557
1. Inside corner
2. Outside corner
(1)
(2)
2
(1)
(2)
Bevel angle Miter angle
45˚ type
52/38˚ type
Right 31.6˚
Left 30˚
Left 31.6˚
Right 31.6˚
Finished piece
guide fence
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.
In the case of right bevel cut
For inside
corner
For outside
corner
For inside
corner
006361
For
outside
corner
45˚ type
Right 35.3˚
Left 35.3˚
Right 35.3˚
006362
15
• The finished piece to be used will
always be on the LEFT side of the blade
after the cut has been made.
Table (A)
Bevel angle
Molding
position in
52/38˚ type
45˚ type
Fig. A
(1)
(2)
Right 33.9˚ Right 30˚
(3)
(4)
Table (B)
Molding
Molding edge against
position in
guide fence
Fig. A
Wall contact edge should be
(1)
against guide fence.
(2)
Ceiling contact edge should
be against guide fence.
(3)
Wall contact edge should be
(4)
against guide fence.
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
• Tilt and secure bevel angle setting to
33.9° RIGHT.
• Adjust and secure miter angle setting to
31.6° RIGHT.
• Lay crown molding with its broad back
(hidden) surface down on the turn base
with its WALL CONTACT EDGE against
the guide fence on the saw.
• The finished piece to be used will
always be on the RIGHT side of the
blade after the cut has been made.
006363
Miter angle
45˚ type
52/38˚ type
Right 31.6˚
Right 35.3˚
Left 35.3˚
Left 31.6˚
Right 31.6˚
Right 35.3˚
006364
Finished piece
Finished piece
will be on the
Right side of
blade.
Finished piece
will be on the
Left side of
blade.