Dust Extraction; General Safety Instructions - stayer SC250W Manual De Instrucciones

6.Never expose your hands or any other part of your body to he
cutting path.
7.Never allow the head that holds the disk to remain in an
undetermined position unless the operator is mandatorily
grasping the control grip 4.
8.For any break between cuttings, however short it may be,
always use the automatic lock of the head in the upper
position by raising the head to the upper stopper.
9.Each time that the machine remains at rest, leave it in the
lower resting position by placing the head at 90º vertical and
0º horizontal, protecting by means of the stationary guard
34 and finally locking it by lowering the head and pushing
button 30.
2.Preventing projections of the cut workpiece
So as to carry out the cutting of workpieces using a stopper,
this latter must be foldable or movable. Once the operator has
selected the cutting range and firmly fixed the workpiece to
the table, he/she will remove the stopper so as to prevent the
workpiece as cut from wedging between the stopper and the
disk.

16.Dust extraction

IMAGE C
All models are prepared for mounting equipment (not included)
for the aspiration of particles generated during the cutting
operation.
The extraction equipment shall be coupled to the particle outlet
nozzle 20.
Mechanical protective equipment
IMAGES V X
1.General protective casing 1.
2.Tiltable protective hood 5.
3.Lower stationary guard 34.
4.Movable guard of the upper table 26.
Electrical protective equipment
1.Class II electrical insulation.
2.Protective module for electrical grid failures so as to
avoid fortuitous starts of a machine after recovery after
a cut off of the electrical supply.

17.General safety instructions

WARNING! When using electrical tools, the essential
safety precautions should always be taken to reduce
the risks of fire, electrical shock and personal damages,
including the following.
Read these instructions with attention before using this
product, and store them.
18.Regular cleaning, maintenance and
greasing
WARNING! .Desenchufar the plug before performing any
adjustment or maintenance comeback.
ENGLISH
57
Cleaning
Clean the machine starting with a brush or with a flat brush
so as to remove sawdust and with a soft cloth.
If compressed air is available, complete cleaning by
blowing with the compressed air pistol.
Maintenance
After each 2,000 hours of use or each two years the
electrical tool must be sent to the official technical service
for maintenance and complete revision.
Before each use, check nuts and joints to detect any
vibration issues and use. If there are gaps take the
machine to service.
Except squeeze and brush change, the machine does not
require any special maintenance by the user. Keep the
machine clean and use it correctly.
Regularly have the correctness of the adjustments
checked by a sufficiently trained user. In the case of any
failure, contact our technical service.
Changing brushes
Warning!
Always use the brushes as supplied by the official technical
service.
1.Remove screw 48.
2.Remove lid 47.
3.Remove screw 50.
4.Move pressing spring 51 to the left.
5.Extract used 52 brush from the brush holder 49.
6.Insert new brush into the brush holder 49.
7.Place pressing spring 51 over the brush.
8.After applying the brush connector tighten screw 50.
9.Position lid 47.
10.Tighten screw 48.
Greasing
This machine does not require any specific greasing by
the user. Specific greasing of the electrical tool will be
carried out on the occasion of the regular maintenance
revisions at the official technical service.
19.Repair service of the manufacturer or
commercial agent:
Calle Sierra de Cazorla, 7
Área Empresarial Andalucía - Sector 1
28320 PINTO (MADRID)
20.List of parts that may be replaced by the
user
IMAGES Y Z
1.Cutting disk 21.
2.Lower stationary guard 34.
3.Movable guard 26.
4.Brushes 52.
5.Guides for adjusting the cutting depth at the lower table
41 .
6.Guides for adjusting the cutting depth at the lower table
27.
57