Milwaukee 6088-30 Manual Del Operador página 2

READ ALL SAFETY WARNINGS AND INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference
The term "power tool" in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark areas invite ac-
cidents.
• Do not operate power tools in explosive atmospheres, such as in
the presence of fl ammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will reduce risk of electric
shock.
• Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an extension cord suit-
able for outdoor use. Use of a cord suitable for outdoor use reduces the
risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal
injury.
• Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce personal
injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your fi nger on the switch
or plugging in power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust-related hazards.
page 2
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool for your ap-
plication. The correct power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
• Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in the hands of untrained
users.
• Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc., in accordance with
these instructions, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
• Have your power tool serviced by a qualifi ed repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
Safety Warnings Common for Grinding, Sanding, Wire Brushing or
Abrasive Cutting-Off Operations:
• This power tool is intended to function as a grinder, sander, wire
brush or cut-of tool. Read all safety warnings, instructions, illus-
trations and specifi cations provided with this power tool. Failure to
follow all instructions listed below may result in electric shock, fi re and/or
serious injury.
• Operations such as polishing are not recommended to be performed
with this power tool. Operations for which the power tool was not de-
signed may create a hazard and cause personal injury.
• Do not use accessories which are not specifi cally designed and
recommended by the tool manufacturer. Just because the accessory
can be attached to your power tool, it does not assure safe operation.
• The rated speed of the accessory must be at least equal to the
maximum speed marked on the power tool. Accessories running faster
than their rated speed can break and fl y apart.
• The outside diameter and the thickness of your accessory must
be within the capacity rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or controlled.
• The arbour size of wheels, fl anges, backing pads or any other acces-
sory must properly fi t the spindle of the power tool. Accessories with
arbour holes that do not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause loss of control.
• Do not use a damaged accessory. Before each use inspect the
accessory such as abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped, inspect for damage or
SERVICE