Before Use; During Use; After Use - Silva CROSS TRAIL 6 Manual

FULL VERSION MANUAL
CROSS TRAIL 6
Art. No: 37815
PRODUCT OVERVIEW
The Cross Trail 6 packaging consists of the following parts:
• Lamp unit
• Headband
• Extension cable with helmet strap
• Cable guide (side)
• Cable guide (rear)
• Battery case (4xAA) - with textile sleeve and attachment strap
• 4 pcs AA batteries
• Helmet bracket with adhesive strip
• Bike bracket
• Quick Guide

BEFORE USE

INSERT BATTERIES (4XAA CASE)
Open the battery case and insert four AA batteries. Either Alkaline, Nimh or Lithium batteries
can be used. Please note the battery polarity. Do not mix different brands of batteries. Do not
mix batteries with different levels of discharge.
If you don't intend to use the headlamp for several months, make sure you remove the batter-
ies from the lamp.
ADJUST THE HEADBAND
The head set is ergonomically shaped to give comfortable fit. Use the 2 buckle adjustments
to fit it perfectly to your head. Attach the headlamp in the head bracket by sliding the head-
lamp foot into the snap-in socket.
To remove, slide the headlamp up and out of the bracket.
FLEXIBLE BATTERY CARRYING
The battery pack can be carried in multiple ways; for example on the headband, in a pocket
backpack, on the waist using the extension cable and cable guide back, or mounted on the
bike frame by using the integrated Velcro strap.
MODULAR SYSTEM
In order to move the headlamp body from the headband to either the helmet bracket or the
bike bracket, gently push the lamp upward relative the head plate with head band. Insert the
headlamp body in the new bracket and gently press it down until you hear a click sound.
MOUNTING THE HELMET BRACKET
The helmet bracket comes with pre mounted adhesive on the back for easy mounting on any
helmet. The adhesive is a polyethylene foam tape developed to not damage or cause any
type of weakness to the plastic in your helmet.
Before mounting the helmet bracket on a helmet, make sure the surface is dry and clean.
Remove the protective paper from the adhesive tape on the helmet bracket. Gently press the
helmet bracket to the helmet.
Depending on helmet type, it might be preferable to use the non-flowligt mode which is when
the blue led on the headlamp is off (Helmet mode – Flow light deactivated), when the Cross
Trail 6 is used on a helmet.
MOUNTING THE BIKE BRACKET
The bike handlebar bracket is developed for use on bike handlebars with a dimension be-
tween 25 and 32 mm.

DURING USE

SILVA INTELLIGENT LIGHT® AND FLOW LIGHT
SILVA Intelligent Light® optimizes the light pattern by the unique combination of a long reach
spot light and a close flood light. With less head movements and a clear view of near as well as
far obstacles, you gain the balance and confidence it takes to move fast and perform better.
Our ingenious SILVA Flow Light takes the optimization even further by providing seamless
tuning of the light pattern for your favourite sport. Simply tilting the light downwards makes
the beams wider to brighten up slower activities. When tilting the headlamp upwards, the
light reaches longer to provide perfect vision when you move fast.
SWITCH ON YOUR HEADLAMP
A push button is located on the left side of the headlamp body. This button controls all light
modes.
• To start the headlamp with Flow Light activated press push button with a short press.
A blue led will be turned on which indicates that the flow light mode is on.
• To start the headlamp with Flow Light deactivated press and hold push button for 1
second
• To cycle between the different modes use short presses.
• To turn the headlamp off press and hold button for 1 second
SHORT PRESS
FLOW LIGHT ACTIVATED
MAX
FLOW LIGHT DEACTIVATED
OFF
DEACTIVATED FLOW LIGHT
Flow Light deactivated means that the Light image will remain unchanged even if the
headlamp is tilted up or down. This might be useful when the lamp is mounted on a helmet or
a bike handle bar.
LONG PRESS
MED MIN
OFF OFF
TEMPERATURE CONTROL
The headlamp temperature will increase during use. The headlamp temperature is mainly
depending on light mode, ambient temperature and the airflow (speed). The Cross Trail 6
headlamp is equipped with a temperature control function which prevents the headlamp
body from overheating by reducing the power to the LEDs. This means that the lower the
ambient temperature, the stronger the light output.
Note: Always make sure that the batteries are disconnected when the headlamp is stored in a
closed compartment such as a bag, pocket or similar.
LOW BATTERY WARNING
During operation of the headlamp there will be a low battery warning when 10% of the battery
energy remains. This is done by flashing both LEDs for 1 second and repeated again after 5
seconds.
POWER RESERVE MODE
During operation, the lamp will go into reserve mode when there is 10% power left of the
battery. All LEDs will flash once before the lamp goes into this mode.
Reserve mode can be overridden by pressing the button.
Warning: If you have pressed the button when headlamp is in reserve mode no more low
battery warnings will appear before the headlamp turns OFF.

AFTER USE

MAINTENANCE
To make sure you get maximum performance from your headlamp, clean it regularly with a
damp cloth.
Headset cleaning – wash in washing machine at 40º C.
TECHNICAL SPECIFICATIONS
Weight: headlamp (excluding battery): 78g
Weight batteries: 152g
Battery type: AA (alkaline, NiMH or Li)
Light distance (Max/Med/Min): 140m/80m/50m
Lumen (Max, Med, Min): 600, 250, 80 Lumen
Burn time +20 ºC:
Max/Med/Min: 5h/12h/50h
Burn time -5 ºC:
Max/Med/Min/: 3h/10h/40h
Water resistance: IPX5
Material head lamp body: PC/ABS and Aluminium
Operative temperature range: -10º - +55º C
Storage temperature range: -20 - +35ºC
PROTECT THE ENVIRONMENT.
Headlamp and batteries should be recycled and must not be thrown in the regular trash.
Dispose these items in accordance with applicable local regulations.
WARRANTY
Silva warrants that, for a period of two (2) years*, your Silva product will be substantially free
of defects in materials and workmanship under normal use. Silva's liability under this warranty
is limited to repairing or replacing the product. This limited warranty extends only to the
original purchaser.
If the Product proves defective during the warranty period please contact the original point
of purchase. Make sure to have your proof of purchase on hand when returning the product.
Returns cannot be processed without the original proof of purchase. This warranty does not
apply if the product has been altered, not been installed, operated, repaired, or maintained in
accordance with instructions supplied by Silva, or has been subjected to abnormal physical
or electrical stress, misuse, negligence or accident. Neither does the warranty cover normal
wear and tear. Silva is not responsible for any consequences, direct or indirect, or damage
resultant from use of this product. In no event will Silva's liability exceed the amount paid by
you for the product. Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This war-
ranty is valid and may be processed only in the country of purchase.
* Batteries: one (1) year
For more information please visit www.silva.se