Working In Manual Mode; Working Adjustments; Flow Adjustment Of The Detergent Solution; Adjustment Of The Brushes Pressure - ADIATEK sapphire 65 Uso Y Mantenimiento

GB

WORKING IN MANUAL MODE

The manual model is useful when, in special cases, it
is necessary to carry out separately only the washing
with the brushes or only the drying of the floor.
ATTENTION:
The washing and drying functions, when they are
not carried out simultaneously, represent an im-
proper use of the machine (see under paragraph
"GENERAL RULES OF SECURITY"). If they are car-
ried out separately, it is necessary to forbid the
working areas to the passage of non-authorized
personnel and to signal the areas of moist floors
with suitable signs.
1. Activate the machine (see under paragraph
"STARTING OF THE MACHINE").
2. Pressing the push button (3) the functioning of
manual (MAN) mode is chosen. When the signal
lamp (2) is on, then the machine is functioning in
manual (MAN) mode.
TO CARRY OUT THE WASHING WITH ONLY THE
BRUSHES:
1. Check that the knob of the solution valve (27) is
in the position of optimum flow, depending on the
type of floor and the type of dirt (see under the par-
agraph "FLOW ADJUSTMENT OF THE DETERGENT SO-
LUTION").
2. Press the push button (17) of up/down of the
brushes base to lower the brushes. Once that it is
lowered, the brushes begin to turn. The blinking sig-
nal lamp (16) indicates that the brushes base is low-
ering or raising (the signal remains on when the
brushes base is in working position), while the signal
lamp (18) signals that the brushes are turning.
3. Press the switch (19) to open the solenoid valve
and permit the detergent solution to lower onto the
brushes. The signal lamp (20) will come on, to indi-
cate that the solenoid valve is open.
TO CARRY OUT THE FUNCTION OF ONLY DRYING:
1. Press the push button (11) of up/down squeegee
to lower the squeegee. The signal lamp (12) indicates
that the squeegee is lowering or lifting (the signal
remains on when the squeegee is in working posi-
tion).
2. Press the switch (9) of the suction motor to start
the suction system. The signal lamp (8) indicates that
the machine is drying.
Position the selector (28) forward to choose the for-
ward drive.
Adjust the movement speed in forward with the
push button (21) (see under paragraph "FORWARD
AND BACKWARD MOVEMENT").
Pressing the accelerator pedal, the machine begins
to proceed forward and to work according to the set
functions.
ATTENTION:
In manual mode every function of the machine has
to be activated or deactivated manually.

WORKING ADJUSTMENTS

Both in automatic as in manual mode, during the
first metres check:
1. that the squeegee adjustment guarantees a per-
fect drying result (see under paragraph "ADJUST-
MENT OF THE SQUEEGEE").
2. that the adjustment of the detergent solution
flow is sufficient to wet the floor uniformly avoiding
the leakage of detergent from the splash guards (see
under paragraph "FLOW ADJUSTMENT OF THE DE-
TERGENT SOLUTION").
3. that the brushes pressure permits an efficient
washing action in function of the dirt and the speed
(see under paragraph "ADJUSTMENT OF THE BRUSH-
ES PRESSURE").
FLOW ADJUSTMENT OF THE DETERGENT SOLU-
TION
To adjust the detergent solution quantity that flows
down onto the brushes it is necessary to act upon
the solution valve knob (27) placed on the right of
the steering column, rotating counterclockwise to
increase it and clockwise to reduce it up to close the
flow.
It is convenient to adjust the flow during working
operation and at each adjustment of the brushes
pressure.
26

ADJUSTMENT OF THE BRUSHES PRESSURE

Through the knob (10) it is possible to adjust the
brushes pressure onto the floor in three pre-set pres-
sure levels. We can visualize on the display (1) the
pressure in kg previously set by pressing the push
button (14).
The adjustment occurs in this way both in automatic
and in manual mode.
ATTENTION:
In order not to overload the brushes motor, it is con-
venient to reduce the brushes pressure going from
smooth floors to rough ones (ex. concrete).
The visualization of the led (18) blinking indicates an
overload of the brushes motor. It is therefore neces-
sary to reduce the pressure up to the level where the
blinking warning stops.

ELECTRIC PROTECTION

The machine is equipped with an electronic system
of protection for all components that carry out
functions of power or control. This device blocks the
defective component and indicates on the display (1)
the corresponding alarm from "A1", "A2" and on.
ATTENTION:
To restore the functioning of the component,
turn off and on again the machine acting upon
the key switch. If the problem persists, please
contact the authorized technical assistance.

OVERFLOW DEVICE

In order to avoid serious damages to the suction mo-
tor, the machine is equipped with a mechanical float
that intervenes when the recovery tank is full, clos-
ing the suction. For the machines equipped with
electric float switch (optional), the switching off of
the suction motor and its signal lamp (12) happens
automatically.
When this happens, it is necessary to empty the re-
covery tank (see under paragraph "RECOVERY TANK
EMPTYING AND CLEANING").
GB