Kicker KXM.1 Serie Manual Del Propietário página 6

KICK EQ+ Bass Boost Control: The variable bass boost control on the side of the amplifi er is designed
to give you increased output, 0–18dB, at the selected frequency. A higher BANDWIDTH (Q) setting will
result in a sharper cut at the frequencies above and below the selected center frequency. The setting for this
control is subjective. If you turn it up, you must readjust the input gain control to avoid clipping the amplifi er.
Remote Control-KXARC: With the included KXARC remote control, you have the ability to unlock and
control DSP functions of the amplifi er remotely. 2017 and newer KXM amplifi ers. See page 7 for installation.
KXARC Pairing: Use the pairing button located above the pairing LED to put the KXM amplifi er into pairing
mode. The light will fl ash when the amp is in pairing mode and ready to connect to a KXARC remote; once
connected it will remain solid. Press and hold the pairing button to clear the list of devices.
GAIN MATCHING
In any audio system, the goal is to reach maximum input and output levels without distortion or clipping.
The engineers at KICKER have taken the guesswork, and hassle, out of matching the output voltage of
your source unit to the amplifi er with the Gain Matching feature. To begin, you'll need to download the
KICKER test tones from www.kicker.com/test-tones. The following fi les are available in MP3 and WAV
formats:
1kHz @ 0dBFS, 50Hz @ 0dBFS, 1kHz @ -10dBFS, 50Hz @ -10dBFS, 1kHz @ -5dBFS, 50Hz @ -5dBFS
These test tones are sine waves meant to provide a consistent signal for the KX amplifi er to reference.
The different recording levels are designed to give you the perfect gain match for your application.
0dBFS: Designed for audiophile applications to give you distortion free audio output with the most
dynamic range.
-5dBFS: Designed for normal/daily applications, there will be less dynamic range but higher potential
audio output levels. With this set up you can get some occasional clipping from the amplifi er.
-10dBFS: Designed only for Subwoofer applications, there will be less dynamic range but higher potential
audio output levels. With this set up you can get some clipping from the amplifi er.
Afterwards, use the following procedure to accurately Gain Match your amplifi er(s):
1. Disconnect the speakers from the KX amplifi er.
2. Set all EQ and crossover settings to fl at on your source unit.
3. Play the downloadable fi le from KICKER.com
4. Turn the source unit up to 3/4 volume.
5. Increase the gain of the amplifi er until the Gain LED turns on.
6. Decrease the gain of the amplifi er until the Gain LED turns off.
All level matching circuitry in the KX amplifi ers is at the beginning of the signal chain. If you are going to
use features like bass boost, SHOCwave or EQ settings, it may be necessary to readjust the gain to a
lower setting to compensate for increased output at those frequencies.
Once the amp and source unit are gain matched, you will want to make certain you are not overdriving
your speakers. Use the following procedure:
1. Set the source until volume to 0.
2. Reconnect the speakers to the KX amplifi er.
3. Slowly increase the volume level of the source unit as you listen for audible distortion.
4. If you can hear clipping, decrease the gain of the amplifi er until it is gone.
Likewise, you can use the CLIP indicator feature of the KXARC remote to easily identify which amplifi er's
output is clipping and when.
6
2017 KXM Mono Amp Rev E.indd 6 2017 KXM Mono Amp Rev E.indd 6
GAIN
MATCH
1/16/2017 3:57:16 PM 1/16/2017 3:57:16 PM