Multiplex Heron KIT Instrucciones De Montaje página 24

Parts List Heron KIT
Part No. Description
No. off
1 1 Building instructions
1.1 1 Complaint form, models
1 Decal sheet
2
3 1 L.H. fuselage shell
4 1 R.H. fuselage shell, with fin
5 1 Canopy frame
6 1 Tailplane
7 1 L.H. wing with spar
8 1 R.H. wing with spar
9 1 Left fin moulding
10 1 Glider nose cone (kit version only)
11 1 Clear canopy
12 1 Wheel
Small parts set
20 3 Velcro tape, hook
21 3 Velcro tape, loop
22 2 Canopy latch catch
23 2 Canopy latch tongue
25 1 Battery retaining strap
26 1 "Twin" control surface horn
26.1 4 "Twin 10x20" control surface horn
27 5 Swivel connector barrel
28 5 Socket-head grubscrew
29 1 Allen key
30 2 Aileron pushrod (one Z-bend)
30.1 2 Flap pushrod (one Z-bend)
31 1 Rudder pushrod (one Z-bend)
32 1 Elevator pushrod (one L-bend)
33 1 Clevis
34 4 Cable holder
35 2 Plastic tailplane screw
36 2 Nut
37 4 Screw (wing retaining clip)
38 1 Machine screw (wheel axle)
39 1 Self-locking nut (wheel axle)
40 2 Trim ballast
41 2 O-ring
42 3 Cable tie
43 2 Spacer sleeve
Plastic parts set
50 1 Motor bulkhead
51 1 Battery support plate
52 1 Wheel frame
53 1 L.H. root rib
54 1 R.H. root rib
55 4 Retaining clip
56 1 Wing locking pin
57 1 Dummy tailwheel
58 1 Tailplane spreader plate
59 1 Tailplane screw support (for nuts)
60 1 Elevator horn
61 2 L.H. servo fairing
62 2 R.H. servo fairing
24
GB
Material
Paper
Paper
Printed adhesive film
Moulded Elapor foam
Moulded Elapor foam
Moulded Elapor foam
Moulded Elapor foam
Moulded Elapor foam
Moulded Elapor foam
Moulded Elapor foam
Moulded Elapor foam
Inj.-moulded plastic
Plastic
Plastic
Plastic
Inj.-moulded plastic
Inj.-moulded plastic
Plastic
Inj.-moulded plastic
Inj.-moulded plastic
Metal
Metal
Metal
Metal
Metal
Metal
Metal
Metal
Inj.-moulded plastic
Inj.-moulded plastic
Metal
Metal
Metal
Metal
Metal ball
Plastic
Plastic
Plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
Inj.-moulded plastic
# 21 4276
Dimensions
300 x 1000 mm
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
45 mm Ø
25 x 60 mm
25 x 60 mm
Ready made
Ready made
16 x 200 mm
Ready made
Ready made
Ready made, 6 mm Ø
M3 x 3 mm
1.5 A/F
1 Ø x 60 mm
1 Ø x 70 mm
1 Ø x 50 mm
M2, 1.7 Ø x 121/10 mm
M2
Ready made
M5 x 35 mm
M5
2.2 x 6.5 mm
M3 x 30 mm
M3
13 mm Ø / 9 g
8 x 2 mm
98 x 2.5 mm
3.1 Ø x 6 Ø x 4 mm
Ready made
20 x 60 mm
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made